CWE601 Maytag Wall Oven - Instructions

my wife removed two screws and removed clips with pliers. We ordered part (2 days) it was fast. Installed in less than 5 min. and I only have one arm. We tried to find part locally but with no model # the parts houses could not find it. We found it on your site in less than 10 min. Your graphs and photos made it super easy. Will pass a ... Read more long your site to others. Thanks for being so helpful.

It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Al lI had to do remove the oh swith & attach th e new on & push in place
It took about 5 min. to turn off the electric & to turn it back on.
Glen V

same

We removed the 2 screws at back of oven that hold element on, which took some doing as they were very rusted. We then pulled old element out; this proved a bit difficult because the ends of the old element were stuck in the insulation behind. We had to wiggle the old element back and forth a bit to get it loose from the insulation. Oth ... Read more er than that, it was easy.

Removed back of stove - 4 screws on top, 3 underneath. Unplugged wires from element. Removed element - 2 screws in front and 2 in the back. Installed new element, plugged wires back in, reinstalled back panel.

I read the online instructions sent in by previous diy'ers. the repairs, esp. the heating element replacement went just as described and went really well. I have used the oven and it works beautifully. Total cost of parts was a little over $60.00. Piece of cake!

We took the door off, you have to be careful of the hinges popping back. We put small screwdrivers on each side and held the hinges out, this made the door easy to just stand up and slide back on the hinges. The glass replacement was simple just a few screws. We spent $127.00 on the part and shipping and a new wall oven would have cost ... Read more us $1500.00. Thanks for making this part available.

Removed the screws from the back of the oven to remove the damaged element; removed the electrical connectors and reattached to the new element and screwed it back in

Removed the door by unscrewing two screws holding it to the springs. Then I placed the door face down on a counter top. I removed the screws from each layer of the door and turned each layer over and laid it beside the door. Took care to support glass so it did not fall out and break. When I got to the layer where the seal was, I remove ... Read more d the old seal and replaced it with the new one. Then, I replaced each layer in reverse order. You have to be careful when replacing the layer that goes over the seal that the seal remains in the right place. It has a tendency to slip out of place, so check it before tightening screws. To place the door back on the spring loaded handles, prop the handles open a ways with screw driver handles. This provides a gap so that the door will slip on easily

In my 26 year old oven the screws to remove the element were extremely difficult to remove, but with 6-10 applications of Liquid Wrench and brute strength we finally did. We were a bit concerned with the insulation that was protruding but used electrical tape to secure the wires to the leads for good measure. All was successfull. I lov ... Read more e my Jenn-Aire double oven!

The repair was straight forward. Remove about a million screws and several layers. The only challenge was loosening some baked on screws in the innermost layer. Repair would have been less than an hour if not for those screws. Key advice is to pay attention to the order that each layer went back on. My oven/stove is about 25 years old, ... Read more but works great. The part was backordered at a local appliance part store from May to ???. I ordered it at PartSelect and it was also backordered for a couple of months. I got it delivered to my home from PartSelect before it ever came in from the local store.

My 31 yr. old grandson very carefully took the whole door apart. Took out the broken window and put the new one back in. He was very careful to put every screw back in the original hole. It took him exactly one hour.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.