EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW26P6KW Crosley Washer - Instructions

All Instructions for the CW26P6KW
121 - 135 of 374

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water leaked from bottom of Washing Machine.
1 person found this instruction helpful.
  • Brandon from Lake Elsinore, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done
Was this helpful?
Thank you for voting!
The top load cover would come off in your hand and it was so loose that the lid cover salety switch would not work
1 person found this instruction helpful.
  • David from WINDHAM, NH
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both si des. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking
Was this helpful?
Thank you for voting!
it was spinning slowly or not at all
1 person found this instruction helpful.
  • Louis from FREMONT, NE
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks
Was this helpful?
Thank you for voting!
Hinge Broken
1 person found this instruction helpful.
  • Angela from FACTORYVILLE, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed screw, replaced hinge.
Was this helpful?
Thank you for voting!
Activator device broken off
1 person found this instruction helpful.
  • Sonya from VAIL, AZ
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Easy repair - with the use of a phillips screwdriver, simply remove the old device and replace with the new
Was this helpful?
Thank you for voting!
lid hinge pin broke
1 person found this instruction helpful.
  • Charles from TEMPE, AZ
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
I followed your video instructions. Very good video.
Was this helpful?
Thank you for voting!
Broken lid hinge pins
1 person found this instruction helpful.
  • William from LEXINGTON, KY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I raised the top of the washing machine per video instructions, removed the screws, replaced broken hinges with the new ones. It was simple as that.
Was this helpful?
Thank you for voting!
Tub to pump hose worn out and leaking
1 person found this instruction helpful.
  • steve from WATSON, MN
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Replaced the hose. two clamps and retainers. very basic repair
Was this helpful?
Thank you for voting!
Broken Hinge Pins
1 person found this instruction helpful.
  • Robert from LIVINGSTON, MT
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I used the putty knife to release the spring clips on the machine lid. They are about 3" in from the side of the machine. Then I lifted the top of the washer up holding the lid in place. I then used a screw driver (torx) to remove the hinge from the bottom of the washer top. The lid should come right off. Then I the removed the broken hin ge pins from the back of the lid with a screwdriver and replaced with the new parts. There is a little tab that the pin fits in the lid to assure you have the pin installed correctly. Then I slid the hinge back on the pin and reversed the process reinstalling the hinges and closing the top of the machine over the spring clips and your done. Very easy repair that I completed in less than 15 minutes.
Was this helpful?
Thank you for voting!
Worn belt
1 person found this instruction helpful.
  • Richard from OXFORD, NY
  • Really Easy
  • Less than 15 mins
Rolled the old one off and rolled the new one on.
Was this helpful?
Thank you for voting!
Old hot water inlet hose had budge at both ends.
2 of 5 people found this instruction helpful.
  • Jimmy from MEMPHIS, TN
  • Very Easy
  • Less than 15 mins
  • Pliers
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this helpful?
Thank you for voting!
Made noise on spin cycle
1 of 2 people found this instruction helpful.
  • Les from Moneta, VA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.
Was this helpful?
Thank you for voting!
machine was starting to make noises when spinning
1 of 2 people found this instruction helpful.
  • Virginia from Rockford, IL
  • Really Easy
  • Less than 15 mins
My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.
Was this helpful?
Thank you for voting!
water not draining
1 of 2 people found this instruction helpful.
  • FRANK from CHULA VISTA, CA
  • Really Easy
  • 15 - 30 mins
  • Socket set
changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks
Was this helpful?
Thank you for voting!
Started making loud screeching noise(bad Bearing)
1 of 2 people found this instruction helpful.
  • Michele from Lebanon, PA
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.
Was this helpful?
Thank you for voting!
All Instructions for the CW26P6KW
121 - 135 of 374