EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW26P6KA Crosley Washer - Instructions

All Instructions for the CW26P6KA
61 - 75 of 287

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
No belt and no motor gear
2 of 3 people found this instruction helpful.
  • Matt from Hoboken, NJ
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Wrench set
Pop the top of the washer and use the nutdriver to remove the two screws holding the frontpanel on. Use the nutdriver for two more screws holding the plastic motor cover on. Use nutdriver for the two BIG screws holding the motorplate to the washer frame. After this, I literally beat/chiped/sawed the old motor geat off. Once that was d one, I put the new one on; had to use a hammer to knock it all the way on (try not to damage the clips). Reassemble everything. Flip washer over and place bet around two smaller gears. Rotate main tub gear to feed belt on. Make sure you use the nutdriver to loosen/tighten the motor positioner screws in the slots if things aren't working here.
The only really hard thing was taking the old motor gear off.
Was this helpful?
Thank you for voting!
loud squeal when stopping and leaking
2 of 3 people found this instruction helpful.
  • Michael from Carmel, NY
  • Easy
  • 1- 2 hours
  • Nutdriver, Socket set
Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.
Was this helpful?
Thank you for voting!
The washer was jumping all over the place and leaking water during the spin cycle
4 of 9 people found this instruction helpful.
  • Elmer from Fort Campbell, KY
  • Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
I took out the agitator first, then I took out the inner tub, next I took out the outer tub, and last I took out the transmission assembly. After replacing the snubber I put the transmission assembly back on, then the new outer tub and next the inner tub. Last I put the agitator back on.
Was this helpful?
Thank you for voting!
Noisy on spin cycle
2 of 3 people found this instruction helpful.
  • William B from STURGIS, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos
Was this helpful?
Thank you for voting!
Washing machine was noisy (metal on metal) after the tub filled up and the motor engaged for the wash cycle.
2 of 3 people found this instruction helpful.
  • GARY from Montvale, NJ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I unplugged the machine, tipped it back slightly and rested in on a gallon paint can. I inspected the under side and manually advanced the fan belt to hear if I could hear the noise at the water pump. The pump pulley and shaft was worn and there were metal shavins (small) on surface of pulley.

Then I removed the belt from the p ulley, rested the machine back to normal position, removed front panel (two sheet metal screws on inside top), removed the water pump hoses (htere is water int he hose & pump assembly so you will get some water on floor.

Then I removed the pump and ordered a new one. The installation was the reverse, machine works like new and the washer tub spins better than ever during the final rinse and spin, since the worn water pump was binding and stressing the machine.

Thanks to Part Select - Your website is awesome and your service instructions and user advice gave me the confidence to do the repair myself. I saved $150 - $250 for the repair.
Was this helpful?
Thank you for voting!
Loud grinding noise when I ran the washing machine
1 person found this instruction helpful.
  • Eman from Wood Dale, IL
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set
It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was s tiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00
Was this helpful?
Thank you for voting!
pulley was scraping bottom of pump
1 person found this instruction helpful.
  • Brian from Granbury, TX
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
First , I unlocked top cover and propped; removed front cover. tilted machine back propping front. pump is at lower right corner, removed both hoses, removed belt and three screws. reversed order completing job. You will have some water leakage removing hoses.
Was this helpful?
Thank you for voting!
Washer making noise during cycles
1 person found this instruction helpful.
  • Nat from Baton Rouge, LA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I moved the washer out from the wall. unplugged washer, turned off water. Took off rear plate exposing pump. Disconnected hoses, using dry/wet vac to catch water. Took out three screws holding pump to base of washer and removed pump, belt slipped right off. Set new pump in place and put in screws. Connected hoses, put rear plate back on. Tilted washer back and installed belt on pulleys and motor. Turned on water, plugged in washer, started to wash clothes. Washer works fine and QUIET. I have yet to find the model number on my Maytag washer. I ordered the pump by sight (good pics).
Was this helpful?
Thank you for voting!
Noise
1 person found this instruction helpful.
  • Marylou from Old Forge, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Wrench (Adjustable)
I changed the piece easily
Was this helpful?
Thank you for voting!
crack in tub hose causing washer water to spill on to floor
1 person found this instruction helpful.
  • Bette from S BARRINGTON, IL
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set
raised the top of the washer to get at the front panel screws. Removed the front panel. Removed the cracked hose and installed the new one. Reinstalled the front and top panels.
Was this helpful?
Thank you for voting!
Water leak
1 person found this instruction helpful.
  • Stephen M. from LEWES, DE
  • Really Easy
  • 30 - 60 mins
  • Socket set
Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks.
Re installed rear access cover and front panel.
Was this helpful?
Thank you for voting!
Wouldn't spin after rince
1 person found this instruction helpful.
  • joe from LAWRENCEVILLE, NJ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Followed the great instructions on your video
Was this helpful?
Thank you for voting!
Spin cycle out of Balance - Machine walks from wall
1 person found this instruction helpful.
  • Needham from Leesville, SC
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pu mp hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.
Was this helpful?
Thank you for voting!
Washer made horrible noise when entering the spin cycle.
1 person found this instruction helpful.
  • Lance D. from Broken Arrow, OK
  • Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Socket set
I removed the cover on the back of the machine, detatched the 2 hoses and removed the 3 screws holding in the Vertical Style Pump - with pulley. These screws are 10 mm nut-driver. The cover if I remember correctly was a standard rather than metric so make sure you have both available.

Screwed new part in, re-attached hoses an d replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.

Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.
Was this helpful?
Thank you for voting!
pump bering failure
1 person found this instruction helpful.
  • Robert from Englewood, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it a test then let the wife do a load of wash it worked like new
Was this helpful?
Thank you for voting!
All Instructions for the CW26P6KA
61 - 75 of 287