CW22B8M Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
lid hinge pin broke
1 person
found this instruction helpful.
-
Charles from TEMPE, AZ
- Very Easy
- 15 - 30 mins
-
Screw drivers
I followed your video instructions. Very good video.
Other Parts Used:
Was this helpful?
Thank you for voting!
broken lid hinge
2 of 4 people
found this instruction helpful.
-
loyce from charleston, SC
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I had my boyfriend take the lid off ,then he took off the two old hinges,one was broken,and the he replaced both lid hinges,daving the good one. it was very simple and quick for him.
Iwill use your service again,thanks.
Loyce Floyd
Iwill use your service again,thanks.
Loyce Floyd
Was this helpful?
Thank you for voting!
Water leaked from bottom of Washing Machine.
1 person
found this instruction helpful.
-
Brandon from Lake Elsinore, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done
Was this helpful?
Thank you for voting!
Whasher would not drain
1 person
found this instruction helpful.
-
Robert E from Katy, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Used a water hose to syfen out the water. Placed hose in the tub. Turned outside facet to fill hose. Undid hose outside and allowed to drain. Pulled pump. Order online ( Delv fast 2 days ) .Replaced pump . Works great . Good luck with yours.
Was this helpful?
Thank you for voting!
Motor smoking. occasionally stops working
1 person
found this instruction helpful.
-
Keith from SAINT PETERSBURG, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Removed the front cover of the machine, held in place by 2 screws on top. Removed the ground strap secured to the motor and (2) 3/8 inch bolts holding the motor in place. Next I removed this the lower belt, pulled the motor forward, then disconnected one by one, each individual electrical connector and connected them to the new motor to a
... Read more
ssure the were connected in the proper place. After this was done, the new motor was put into place with the belt reinstalled, ground straps reconnected, and bolted back into position.
Job finished in about 20 minutes.
Job finished in about 20 minutes.
Read less
Was this helpful?
Thank you for voting!
Water leak
2 of 4 people
found this instruction helpful.
-
Joe from Clearfield, PA
- Really Easy
- 15 - 30 mins
-
Socket set
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
Was this helpful?
Thank you for voting!
washing machine squeaked on the spin cycle
1 person
found this instruction helpful.
-
Jeffrey from Wabash, IN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!
Was this helpful?
Thank you for voting!
The water pump went out
1 person
found this instruction helpful.
-
felicia from Broken Arrow, OK
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel t
... Read more
hat you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.
Read less
Was this helpful?
Thank you for voting!
Problem manifested as a loud squealing/grinding noise during all cycles.
1 person
found this instruction helpful.
-
Michael from Atlanta, GA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Disconnected both power and hot and cold input water lines. Laid the washer on its front side for access to the bottom. Removed the small access panel from the back of the machine to remove the metal screws holding the pump in place. Removed the single drive belt. New pump installed easily, replaced the belt and access panel. Reconne
... Read more
cted the power and water hoses and everything worked fine.
Read less
Was this helpful?
Thank you for voting!
Plastic Lid Hinge was broken
2 of 4 people
found this instruction helpful.
-
Thomas from Coral Springs, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Changing the hinge was not difficult, but here's a hint: the top of the washer raises up if you pry it with a big screwdriver- be sure to wrap the screwdriver in a cloth so as not to scratch the appliance. Doing it this way makes it easy to access the retaining screws. You can push the wash tub to one side and reach the screws from undern
... Read more
eath, but they're a tight fit and doing it that way is difficult. Overall a pretty easy repair and I'm only moderately handy.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
end broken on the hinge
1 person
found this instruction helpful.
-
James from Louisville, KY
- Really Easy
- 15 - 30 mins
-
Screw drivers
used putty knife to to raise the top, took out two screws, replaced parts , then closed the top.
Was this helpful?
Thank you for voting!
Water removal pump stopped working.
1 person
found this instruction helpful.
-
Timothy from Palmdale, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Removed lower rear panel by removing 8 screws. Then I removed the two hoses that are attached to the pump by removing the hose clamps with a pair of plyers. The three hex head screws that anchor the pump to the base of the washer unit were removed and the pump came right out. To put the new pump in I just slipped the pump through the hol
... Read more
e at the bottom of the washer and attached the belt onto the pulley. Then reversed the installation process. The washer had to be tipped forward slightly for this process and blocked (approx. 8 in.) to allow access to pulley. Very easy install, no help needed. Washer must be empty and preferable dry when task is done or water will be everywhere.
Read less
Was this helpful?
Thank you for voting!
loud grinding sound then washer would shut down then there was water all over
1 person
found this instruction helpful.
-
marilisa from naples, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set
first removed panel from rear of washer removed hoses and drained water in them, removed the 3 screws and removed the belt then removed the pump. Replaced with new one and put back screws,hoses and belt. walaaa.... it works like new!!!!
Was this helpful?
Thank you for voting!
The water was leaking out from the bottom.
1 person
found this instruction helpful.
-
Doris from Plainsboro, NJ
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
My husband took out the 2 screws in the front panel and loosen the 3 nuts from the pump.
The parts was easily removed and the entire job tooked 30 mins.
The parts was easily removed and the entire job tooked 30 mins.
Was this helpful?
Thank you for voting!
Washer had bad water pump
1 person
found this instruction helpful.
-
Edwin from Eagar,, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed access panel to expose pump, removed drive belt, and old pump, repeated the avove steps in reverse order, tested for leaks and proper operation.
Was this helpful?
Thank you for voting!