EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW20T8W Crosley Washer - Instructions

All Instructions for the CW20T8W
121 - 135 of 415

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hinge Broken
1 person found this instruction helpful.
  • Angela from FACTORYVILLE, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed screw, replaced hinge.
Was this helpful?
Thank you for voting!
Drain pump making load screeching noise
1 person found this instruction helpful.
  • Danny from Fort Worth, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nut driver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
Was this helpful?
Thank you for voting!
The top load cover would come off in your hand and it was so loose that the lid cover salety switch would not work
1 person found this instruction helpful.
  • David from WINDHAM, NH
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both si des. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking
Was this helpful?
Thank you for voting!
it was spinning slowly or not at all
1 person found this instruction helpful.
  • Louis from FREMONT, NE
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks
Was this helpful?
Thank you for voting!
lid hinge pin broke
1 person found this instruction helpful.
  • Charles from TEMPE, AZ
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
I followed your video instructions. Very good video.
Was this helpful?
Thank you for voting!
Broken lid hinge pins
1 person found this instruction helpful.
  • William from LEXINGTON, KY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I raised the top of the washing machine per video instructions, removed the screws, replaced broken hinges with the new ones. It was simple as that.
Was this helpful?
Thank you for voting!
Tub to pump hose worn out and leaking
1 person found this instruction helpful.
  • steve from WATSON, MN
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Replaced the hose. two clamps and retainers. very basic repair
Was this helpful?
Thank you for voting!
Broken Hinge Pins
1 person found this instruction helpful.
  • Robert from LIVINGSTON, MT
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I used the putty knife to release the spring clips on the machine lid. They are about 3" in from the side of the machine. Then I lifted the top of the washer up holding the lid in place. I then used a screw driver (torx) to remove the hinge from the bottom of the washer top. The lid should come right off. Then I the removed the broken hin ge pins from the back of the lid with a screwdriver and replaced with the new parts. There is a little tab that the pin fits in the lid to assure you have the pin installed correctly. Then I slid the hinge back on the pin and reversed the process reinstalling the hinges and closing the top of the machine over the spring clips and your done. Very easy repair that I completed in less than 15 minutes.
Was this helpful?
Thank you for voting!
Activator device broken off
1 person found this instruction helpful.
  • Sonya from VAIL, AZ
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Easy repair - with the use of a phillips screwdriver, simply remove the old device and replace with the new
Was this helpful?
Thank you for voting!
Worn belt
1 person found this instruction helpful.
  • Richard from OXFORD, NY
  • Really Easy
  • Less than 15 mins
Rolled the old one off and rolled the new one on.
Was this helpful?
Thank you for voting!
Motor smoking. occasionally stops working
1 person found this instruction helpful.
  • Keith from SAINT PETERSBURG, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Removed the front cover of the machine, held in place by 2 screws on top. Removed the ground strap secured to the motor and (2) 3/8 inch bolts holding the motor in place. Next I removed this the lower belt, pulled the motor forward, then disconnected one by one, each individual electrical connector and connected them to the new motor to a ssure the were connected in the proper place. After this was done, the new motor was put into place with the belt reinstalled, ground straps reconnected, and bolted back into position.
Job finished in about 20 minutes.
Was this helpful?
Thank you for voting!
Whasher would not drain
1 person found this instruction helpful.
  • Robert E from Katy, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Used a water hose to syfen out the water. Placed hose in the tub. Turned outside facet to fill hose. Undid hose outside and allowed to drain. Pulled pump. Order online ( Delv fast 2 days ) .Replaced pump . Works great . Good luck with yours.
Was this helpful?
Thank you for voting!
Water removal pump stopped working.
1 person found this instruction helpful.
  • Timothy from Palmdale, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Removed lower rear panel by removing 8 screws. Then I removed the two hoses that are attached to the pump by removing the hose clamps with a pair of plyers. The three hex head screws that anchor the pump to the base of the washer unit were removed and the pump came right out. To put the new pump in I just slipped the pump through the hol e at the bottom of the washer and attached the belt onto the pulley. Then reversed the installation process. The washer had to be tipped forward slightly for this process and blocked (approx. 8 in.) to allow access to pulley. Very easy install, no help needed. Washer must be empty and preferable dry when task is done or water will be everywhere.
Was this helpful?
Thank you for voting!
loud grinding sound then washer would shut down then there was water all over
1 person found this instruction helpful.
  • marilisa from naples, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
first removed panel from rear of washer removed hoses and drained water in them, removed the 3 screws and removed the belt then removed the pump. Replaced with new one and put back screws,hoses and belt. walaaa.... it works like new!!!!
Was this helpful?
Thank you for voting!
The water was leaking out from the bottom.
1 person found this instruction helpful.
  • Doris from Plainsboro, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
My husband took out the 2 screws in the front panel and loosen the 3 nuts from the pump.

The parts was easily removed and the entire job tooked 30 mins.
Was this helpful?
Thank you for voting!
All Instructions for the CW20T8W
121 - 135 of 415