EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW20T8A Crosley Washer - Instructions

All Instructions for the CW20T8A
121 - 135 of 326

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
would not engage spin cycle, belt was shredding.
1 person found this instruction helpful.
  • john from mashpee, MA
  • Really Easy
  • Less than 15 mins
pulled the machine out, tilted it backward to expose the bottom. pulled off the old belt. got the new belt started on the three pulleys. pulled the belt to spin it , and...............done !!
Was this helpful?
Thank you for voting!
Had a squeaky belt
1 person found this instruction helpful.
  • Michael from Mokena, IL
  • Really Easy
  • Less than 15 mins
Piece of cake. Raise up the front of the machine. the belt slips of easy by turning the main drive wheel. put the belt on the two small one and then rotate the big wheel as you slip the belt into the grove. good idea to first clean the wheels of any old belt material that may be worn off. Piece of cake!
Was this helpful?
Thank you for voting!
Broken belt needed to be replaced.
1 person found this instruction helpful.
  • Niels from Hopewell Junction, NY
  • Easy
  • Less than 15 mins
  • Socket set, Wrench (Adjustable)
Replacing a belt on a washing machine is a pretty easy process, depending slightly on how easy it is to access the belt. On our Maytag, the belt can be accessed directly underneith the washing machine. So, I lifted the front of the machine and put a few blocks of scrap wood under the legs to hold up the front of the machine. Once that was done, there was nothing else that needed to be removed to access the pullies that the belt had to go around. The motor itself is generally adjustable to allow the belt to be changed. So, I first wrapped the belt around the largest one that spins the washin machine tub, and then wrapped it around the one that spins the water pump. Finally, I loosened the bolt on the motor to allow it to move, wrapped the belt around the motor, pulled the motor back to tighten up the belt, and tightened the bolt that holds the motor in place. It's a pretty straight forward repair that narly anyone could do thmselves.
Was this helpful?
Thank you for voting!
Locked up the machine.
1 person found this instruction helpful.
  • Mitchell B. from Moreno Valley, CA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the machine up . Worked perfect.











the
Was this helpful?
Thank you for voting!
Wore out Pulley/Bearing
1 person found this instruction helpful.
  • Mark from Akron, CO
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Disconnect all water supply and unplug washer. Remove 3 screws on back panel of the washer. This will expose the pump unit. Detach belt on the bottom of the washer. Then detach two hoses that connects to the pump unit. Use pliers if necessary to disconnect hoses. Use 5/16 socket with extension to take out three bolts the connect pump to t he washer. That's it, now replace old pump unit and with new. Place bolts back in the 3 holes, reattached hoses, cover the back with 3 scres. Connect the belt to the pulley system on the bottom. Connect water supply and plug it in.
Was this helpful?
Thank you for voting!
Machine was wailing like a stuck pig!
1 person found this instruction helpful.
  • Jeff from Sugar Land, TX
  • Really Easy
  • Less than 15 mins
Pulled that sucker out from the wall and leaned him back just enough to prop a case a beer under it. Slid up under there with the biggest dust bunny I ever seen. Yanked that old belt off and threw it away. Tried to uncoil the new one and it slapped me in the nose! Got it uncoiled and around the two smaller pulleys pulling the adjustable o ne in to it's limit and walked the belt around the big drum pulley. By the time my wife put down her coffee and came to see if she can lend me a hand I was done!.
Was this helpful?
Thank you for voting!
it was spinning slowly or not at all
1 person found this instruction helpful.
  • Louis from FREMONT, NE
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks
Was this helpful?
Thank you for voting!
pulley got hot and broke
1 of 2 people found this instruction helpful.
  • Russell from LOS MOLINOS, CA
  • Really Easy
  • Less than 15 mins
  • Wrench (Adjustable)
replaced pulley and belt. Looked for a pulley for 1 week at retail stores. Found pulley on parts select
Was this helpful?
Thank you for voting!
Started making loud screeching noise(bad Bearing)
1 of 2 people found this instruction helpful.
  • Michele from Lebanon, PA
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.
Was this helpful?
Thank you for voting!
Broken Belt and Motor Pulley
1 of 2 people found this instruction helpful.
  • Jeffrey from Flat Rock, MI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Repair was very easy. I removed the old pulley from the motor shaft by breaking it. And then tapped the new one into place. It works great. DON'T buy a new motor for $120, just replace the pulley $6. This whirlpool pulley fits the Admiral motor perfectly!
Was this helpful?
Thank you for voting!
Made noise during washing and rinse cycle
1 of 2 people found this instruction helpful.
  • Jose from Elizabeth, NJ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
It was easy to replace the water pump
Was this helpful?
Thank you for voting!
Water pump replacement
1 of 2 people found this instruction helpful.
  • Lon from Morton Grove, IL
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Socket set
Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump

Reverse the process to install a new pump

Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.

The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.

This was is 1st time we used your server but it won’t be the last!

Kudos to the entire staff and please…keep up the good work.

Sincerely,

Lon Thomas
Was this helpful?
Thank you for voting!
Made noise on spin cycle
1 of 2 people found this instruction helpful.
  • Les from Moneta, VA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.
Was this helpful?
Thank you for voting!
machine was starting to make noises when spinning
1 of 2 people found this instruction helpful.
  • Virginia from Rockford, IL
  • Really Easy
  • Less than 15 mins
My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.
Was this helpful?
Thank you for voting!
Old hot water inlet hose had budge at both ends.
2 of 5 people found this instruction helpful.
  • Jimmy from MEMPHIS, TN
  • Very Easy
  • Less than 15 mins
  • Pliers
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this helpful?
Thank you for voting!
All Instructions for the CW20T8A
121 - 135 of 326