EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW20T6WC Crosley Washer - Instructions

All Instructions for the CW20T6WC
106 - 120 of 391

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Wouldn't spin after rince
1 person found this instruction helpful.
  • joe from LAWRENCEVILLE, NJ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Followed the great instructions on your video
Was this helpful?
Thank you for voting!
crack in tub hose causing washer water to spill on to floor
1 person found this instruction helpful.
  • Bette from S BARRINGTON, IL
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set
raised the top of the washer to get at the front panel screws. Removed the front panel. Removed the cracked hose and installed the new one. Reinstalled the front and top panels.
Was this helpful?
Thank you for voting!
Water leak
1 person found this instruction helpful.
  • Stephen M. from LEWES, DE
  • Really Easy
  • 30 - 60 mins
  • Socket set
Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks.
Re installed rear access cover and front panel.
Was this helpful?
Thank you for voting!
Washer making noise during cycles
1 person found this instruction helpful.
  • Nat from Baton Rouge, LA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I moved the washer out from the wall. unplugged washer, turned off water. Took off rear plate exposing pump. Disconnected hoses, using dry/wet vac to catch water. Took out three screws holding pump to base of washer and removed pump, belt slipped right off. Set new pump in place and put in screws. Connected hoses, put rear plate back on. Tilted washer back and installed belt on pulleys and motor. Turned on water, plugged in washer, started to wash clothes. Washer works fine and QUIET. I have yet to find the model number on my Maytag washer. I ordered the pump by sight (good pics).
Was this helpful?
Thank you for voting!
broken lid hinge
2 of 4 people found this instruction helpful.
  • loyce from charleston, SC
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
I had my boyfriend take the lid off ,then he took off the two old hinges,one was broken,and the he replaced both lid hinges,daving the good one. it was very simple and quick for him.

Iwill use your service again,thanks.
Loyce Floyd
Was this helpful?
Thank you for voting!
Water leaked from bottom of Washing Machine.
1 person found this instruction helpful.
  • Brandon from Lake Elsinore, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done
Was this helpful?
Thank you for voting!
Drain pump making load screeching noise
1 person found this instruction helpful.
  • Danny from Fort Worth, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nut driver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
Was this helpful?
Thank you for voting!
Hinge Broken
1 person found this instruction helpful.
  • Angela from FACTORYVILLE, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed screw, replaced hinge.
Was this helpful?
Thank you for voting!
lid hinge pin broke
1 person found this instruction helpful.
  • Charles from TEMPE, AZ
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
I followed your video instructions. Very good video.
Was this helpful?
Thank you for voting!
The top load cover would come off in your hand and it was so loose that the lid cover salety switch would not work
1 person found this instruction helpful.
  • David from WINDHAM, NH
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both si des. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking
Was this helpful?
Thank you for voting!
it was spinning slowly or not at all
1 person found this instruction helpful.
  • Louis from FREMONT, NE
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks
Was this helpful?
Thank you for voting!
Washer had bad water pump
1 person found this instruction helpful.
  • Edwin from Eagar,, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Removed access panel to expose pump, removed drive belt, and old pump, repeated the avove steps in reverse order, tested for leaks and proper operation.
Was this helpful?
Thank you for voting!
loud grinding sound then washer would shut down then there was water all over
1 person found this instruction helpful.
  • marilisa from naples, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
first removed panel from rear of washer removed hoses and drained water in them, removed the 3 screws and removed the belt then removed the pump. Replaced with new one and put back screws,hoses and belt. walaaa.... it works like new!!!!
Was this helpful?
Thank you for voting!
The water was leaking out from the bottom.
1 person found this instruction helpful.
  • Doris from Plainsboro, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
My husband took out the 2 screws in the front panel and loosen the 3 nuts from the pump.

The parts was easily removed and the entire job tooked 30 mins.
Was this helpful?
Thank you for voting!
washing machine squeaked on the spin cycle
1 person found this instruction helpful.
  • Jeffrey from Wabash, IN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!
Was this helpful?
Thank you for voting!
All Instructions for the CW20T6WC
106 - 120 of 391