CW20P8WSC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water leak
1 person
found this instruction helpful.
-
Stephen M. from LEWES, DE
- Really Easy
- 30 - 60 mins
-
Socket set
Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks.
Re installed rear access cover and front panel.
Re installed rear access cover and front panel.
Was this helpful?
Thank you for voting!
My 24 year old Maytag performance washer started occasionally not agitating. Eventually it did not agitate at all but would spin.
1 person
found this instruction helpful.
-
Loretta from LEBANON JCT, KY
- Really Easy
- 30 - 60 mins
-
Screw drivers
The lid switch is on the right side top of the washer under the lid. I took a putty knife and found the clips that hold the top of the washer and pushed them to release it. I then lifted it up to fully see the lid switch. I unplugged the washer from the wall socket and took out the 2 screws that holds the lid switch in. Then unplugged the
... Read more
lid switch from its electrical connection and put the new one in its place. Washer is working great so far.
Read less
Was this helpful?
Thank you for voting!
Wouldn't spin after rince
1 person
found this instruction helpful.
-
joe from LAWRENCEVILLE, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Followed the great instructions on your video
Was this helpful?
Thank you for voting!
Spin cycle out of Balance - Machine walks from wall
1 person
found this instruction helpful.
-
Needham from Leesville, SC
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pu
... Read more
mp hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.
Read less
Was this helpful?
Thank you for voting!
Water leak
2 of 4 people
found this instruction helpful.
-
Joe from Clearfield, PA
- Really Easy
- 15 - 30 mins
-
Socket set
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
Was this helpful?
Thank you for voting!
Loud grinding noise when I ran the washing machine
1 person
found this instruction helpful.
-
Eman from Wood Dale, IL
- Easy
- 30 - 60 mins
-
Pliers, Socket set
It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was s
... Read more
tiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00
Read less
Was this helpful?
Thank you for voting!
Whasher would not drain
1 person
found this instruction helpful.
-
Robert E from Katy, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Used a water hose to syfen out the water. Placed hose in the tub. Turned outside facet to fill hose. Undid hose outside and allowed to drain. Pulled pump. Order online ( Delv fast 2 days ) .Replaced pump . Works great . Good luck with yours.
Was this helpful?
Thank you for voting!
loud grinding sound then washer would shut down then there was water all over
1 person
found this instruction helpful.
-
marilisa from naples, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set
first removed panel from rear of washer removed hoses and drained water in them, removed the 3 screws and removed the belt then removed the pump. Replaced with new one and put back screws,hoses and belt. walaaa.... it works like new!!!!
Was this helpful?
Thank you for voting!
The water was leaking out from the bottom.
1 person
found this instruction helpful.
-
Doris from Plainsboro, NJ
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
My husband took out the 2 screws in the front panel and loosen the 3 nuts from the pump.
The parts was easily removed and the entire job tooked 30 mins.
The parts was easily removed and the entire job tooked 30 mins.
Was this helpful?
Thank you for voting!
Washer had bad water pump
1 person
found this instruction helpful.
-
Edwin from Eagar,, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed access panel to expose pump, removed drive belt, and old pump, repeated the avove steps in reverse order, tested for leaks and proper operation.
Was this helpful?
Thank you for voting!
end broken on the hinge
1 person
found this instruction helpful.
-
James from Louisville, KY
- Really Easy
- 15 - 30 mins
-
Screw drivers
used putty knife to to raise the top, took out two screws, replaced parts , then closed the top.
Was this helpful?
Thank you for voting!
Water removal pump stopped working.
1 person
found this instruction helpful.
-
Timothy from Palmdale, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Removed lower rear panel by removing 8 screws. Then I removed the two hoses that are attached to the pump by removing the hose clamps with a pair of plyers. The three hex head screws that anchor the pump to the base of the washer unit were removed and the pump came right out. To put the new pump in I just slipped the pump through the hol
... Read more
e at the bottom of the washer and attached the belt onto the pulley. Then reversed the installation process. The washer had to be tipped forward slightly for this process and blocked (approx. 8 in.) to allow access to pulley. Very easy install, no help needed. Washer must be empty and preferable dry when task is done or water will be everywhere.
Read less
Was this helpful?
Thank you for voting!
Hinge Broken
1 person
found this instruction helpful.
-
Angela from FACTORYVILLE, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed screw, replaced hinge.
Was this helpful?
Thank you for voting!
Water leaked from bottom of Washing Machine.
1 person
found this instruction helpful.
-
Brandon from Lake Elsinore, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done
Was this helpful?
Thank you for voting!
Drain pump making load screeching noise
1 person
found this instruction helpful.
-
Danny from Fort Worth, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nut ... Read more driver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nut ... Read more driver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
Read less
Was this helpful?
Thank you for voting!