CW20P8WC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Made noise on spin cycle
1 of 2 people
found this instruction helpful.
-
Les from Moneta, VA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.
Other Parts Used:
Was this helpful?
Thank you for voting!
Started making loud screeching noise(bad Bearing)
1 of 2 people
found this instruction helpful.
-
Michele from Lebanon, PA
- Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.
Was this helpful?
Thank you for voting!
Lid hinges wear out, causing lid to slam as you are trying to put clothes in or take them out.
1 of 2 people
found this instruction helpful.
-
Jan from Challis, ID
- Easy
- Less than 15 mins
-
Screw drivers
Lift the top of the washer so you can access the screws that hold the hinges. Replace the hinges,and close the washer top. This is the sescond time we have had to replace the hinges.
This lid and hinges are very poorly designed. Instead of opening to the side, it opens straight back. That means when the hinges wear out (an ... Read more d they do because they are plastic), you have to push the lid all the way back to stay open. When you push it all the way back, it hits the control knob and turns off the water.
If you are like me, I like to turn the water on and add the soap so it can dissolve before I add the clothes. It is really irritating when you open the lid and the only way for it to stay open is to push it all the way back and the water shuts off. And if you don't push it all the way back, it slams and scares the bejeebers out of you or slams on your fingers.
This lid and hinges are very poorly designed. Instead of opening to the side, it opens straight back. That means when the hinges wear out (an ... Read more d they do because they are plastic), you have to push the lid all the way back to stay open. When you push it all the way back, it hits the control knob and turns off the water.
If you are like me, I like to turn the water on and add the soap so it can dissolve before I add the clothes. It is really irritating when you open the lid and the only way for it to stay open is to push it all the way back and the water shuts off. And if you don't push it all the way back, it slams and scares the bejeebers out of you or slams on your fingers.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer wouldn't spin because the switch on the lid broke
2 of 5 people
found this instruction helpful.
-
Rachelle from Eagle Mountain, UT
- Really Easy
- Less than 15 mins
-
Screw drivers
I unscrewed the old lid switch and screwed on the new switch in seriously 2 minutes!
Was this helpful?
Thank you for voting!
Broken Hinge Pin
1 of 2 people
found this instruction helpful.
-
John from Dover, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I followed the feed back in the forum from a previous repair. I popped open the top of the Washing and propped it open @ approx. 70 degrees,moved the Tub out of the way and used a small Phillips Scwdrvr to remove the broken part, installing the new parts was a snap, I took the time to use a Q-Tip and petroleum jelly to coat the pin and hi
... Read more
nge making it easier and less binding when opening the lid.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Made noise during washing and rinse cycle
1 of 2 people
found this instruction helpful.
-
Jose from Elizabeth, NJ
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
It was easy to replace the water pump
Other Parts Used:
Was this helpful?
Thank you for voting!
broken lid hinge
1 of 2 people
found this instruction helpful.
-
dorris from slaughters, KY
- Easy
- 15 - 30 mins
-
Screw drivers
short drive, 90 degree, "star" driver. push tub to side and back to reach lower part of old hinge, remove single screw. (careful not to drop it into the "mechanics" of the tub.) repeat for the other side. remove parts from lid. reassemble new parts onto lid, along with lower hinge parts. secure the lower hinge to door part(s) with maski
... Read more
ng tape to hold in place. hold lid in place over lower hinge screw holes and start screws by hand. snug up the screws and your done! the 'STAR" screws may be relpaced with similar "phillips" so you wont have to scrounge for a "star" driver the next time.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water pump replacement
1 of 2 people
found this instruction helpful.
-
Lon from Morton Grove, IL
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Socket set
Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process ... Read more to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process ... Read more to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
Read less
Was this helpful?
Thank you for voting!
The Pump Went Out & Water Was All Over My Floor..
1 of 2 people
found this instruction helpful.
-
BILL from DIX, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .
Was this helpful?
Thank you for voting!
Lid hinge pin broken
1 of 2 people
found this instruction helpful.
-
Harvey from East Brunswick, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
Opened hinges top of washer. Removed screws holding hinge bases. Removed the washer top lid and unscrewd broken hinge pin. Replaced hinge pin and inserted in pin base and screwd base op hinge back onto washer and job was done.
Was this helpful?
Thank you for voting!
Washing machine began making a screeching noise but only during the spin cycle - when it was emptying the water from the tub. After a few uses the machine just stopped working.
1 of 2 people
found this instruction helpful.
-
Patricia from Modesto, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
The pump was easy enough to replace. Access panel in the back and 3 screws and it was off and back on in less than 20 minutes. It was putting the belt on that gave me the most trouble even though one of the pulleys moved to allow for easy replacement it did not move enough. It took me another 30 minutes just to get the belt on. I fina
... Read more
lly decided to place the belt on the two smaller pulleys and save the larger one for last and it went on with no trouble at all. Learn from my error =]
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
discharge pulley assembly bearing going out on it.
1 of 2 people
found this instruction helpful.
-
Milton from bartlett, IL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and d
... Read more
id a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.
Read less
Was this helpful?
Thank you for voting!
Washer making loud noise and tub off balance
1 of 2 people
found this instruction helpful.
-
Hollee from Rancho Mirage, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I followed Gary from Sioux City IA instructions. Very well explained.
Was this helpful?
Thank you for voting!
noisy out of balance during spin cycles
1 of 2 people
found this instruction helpful.
-
Ronald from Wading River, NY
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Socket set
I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise
... Read more
!
Read less
Was this helpful?
Thank you for voting!
Broken lid hinge pin
1 of 3 people
found this instruction helpful.
-
PAT from ALBUQUERQUE, NM
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
It took two of us to move aqnd hold the tub so we could install the hinge. I would not say it was easy to accomplish this.
Other Parts Used:
Was this helpful?
Thank you for voting!