CW20P8HSC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Under belt was used and ready to let go..
0 of 1 people
found this instruction helpful.
-
Melanie from Tamarac, FL
- Really Easy
- Less than 15 mins
First I am a woman and was able to do it, and if I can do it anyone should be able to do this. The service call alone was 75.00, and the belt was 23.00 with shipping. First we tilted the washer at a 45 degree angle and I removed the belt, and just rolled the newer one on the track. That was it and I was done. My washer now purrs like a ki
... Read more
tten love it. And Part Select sent out my part and I recieved it next day, thank you for wonderful service that kind of service is hard to find. <3
Read less
Was this helpful?
Thank you for voting!
the lower panel rotted away and damaged the pump
0 of 1 people
found this instruction helpful.
-
kenneth from wayland, NY
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
this email does not include the rest of the parts i ordered. i had to replace the pump and the base panel of the washer as it was rotten. i had to open the top, remove the front panel and change out the base and install the pump. your parts and website were very helpful. thank you however this will be the last maytag i will purchase
... Read more
.
Read less
Was this helpful?
Thank you for voting!
Water would not drain and tub would not spin.
0 of 1 people
found this instruction helpful.
-
Larry from Waukesha, WI
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I had to raise the top of the washer and take off the front pannel. It was not too hard to replace the pump except that it was in the back corner and it was hard to reach the bolts to remove and install the new pump.
Was this helpful?
Thank you for voting!
drive pulley broke off from drain pump
0 of 1 people
found this instruction helpful.
-
John from Pomfret, MD
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Raised washer. Identified problem. Removed from panel, gaining access to drain pump. Removed hoses, replaced pump. NOTE: I used blue Loctite on pump mounting bolts. Reinstalled from panel, lowered washer, cleaned drum. Ran one (1) cycle with hot water and bleach ONLY.
Was this helpful?
Thank you for voting!
Washer going out of balance
0 of 1 people
found this instruction helpful.
-
Brian from Rock Hill, SC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Tilted washer back and removed belt
Lifted front of top and propped up
Unscrewed two screws and removed front of washer
Disconnected two drain lines from tub
Disconnected 6 springs from tub
Removed tub
Popped off bottom plastic cap
Removed locking ring
Slid off gear from shaft
Unbolted screws f ... Read more rom snubber support ring
replaced snubber
Put everything back together in reverse order
Worked like a champ!!!!!
Lifted front of top and propped up
Unscrewed two screws and removed front of washer
Disconnected two drain lines from tub
Disconnected 6 springs from tub
Removed tub
Popped off bottom plastic cap
Removed locking ring
Slid off gear from shaft
Unbolted screws f ... Read more rom snubber support ring
replaced snubber
Put everything back together in reverse order
Worked like a champ!!!!!
Read less
Was this helpful?
Thank you for voting!
Vibration
0 of 1 people
found this instruction helpful.
-
Richard from Jacksonville, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Troubleshoot problem, removed front, removed drive belt, removed pump with pulley. Note, new pump did not have black plate, installed worked great.Thanks
Was this helpful?
Thank you for voting!
Belt was frayed and pump was leaking.
0 of 1 people
found this instruction helpful.
-
Glenn from Kansasville, WI
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
I removed the back panel and then removed the old pump. After attaching the new pump I flipped the machine and attached the new belt. I put everything back together and voila, the machine works.
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer shook and danced on basement floor
0 of 1 people
found this instruction helpful.
-
Bruce H from Mason City, IA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
I found on-line that replacing the snubber ring may fix the problem and ordered the part. With the instructions also downloaded I started taking the washer apart. Without the instructions the task would have been more difficult and possibly disastrous as I might have taken the bolts out that tighten down the snubber ring. All went well wi
... Read more
th a little patience. The washer works good.
Read less
Was this helpful?
Thank you for voting!
Had some difficulty placing pulley back in place
0 of 1 people
found this instruction helpful.
-
Oscar from Weslaco, TX
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Laid washer on its side, released five of the six tub springs, then removed the dive belt and the main pulley. With some effort removing the old snubber ring, placed the new snubber in place. After fighting with the large spring under the pulley I was able to replaced the six screws with the help of an assistant. Replaced the pulley, b
... Read more
elt and the five springs. Closed the unit up and placed all the hoses back in place. I was amazed at how smooth the washer functioned with no vibration at all! Thank You.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
when in spin cycle it would shake rattle &roll
0 of 1 people
found this instruction helpful.
-
Marvin from Manteca, CA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers
open top,remove back panel.then laid on the side and removed belt.remove hose from tub to pump.removed small hose for fill level.Hard part was to remove springs from tub.Then pull tub and transmission out of housing.Remove pulley from shaft.Lossen screws around snubber ring but do not remove them.Remove old snubber ring.clean surfaces wit
... Read more
h alcohol.install new snubber ring and assemble in reverse order.
Read less
Was this helpful?
Thank you for voting!
My washer had stopped turning. It wouldn't wash or spin but the moter was still working.
1 of 5 people
found this instruction helpful.
-
Evelyn from Temple, TX
- Really Easy
- Less than 15 mins
We're not repair people. So when calling around for the replacement belt no one had it. Everyone said that the belt went to a dryer. We simply inspected the machine. Located the worn belt which was on the bottom of the washer machine went online and ordered the belt. Thank you so much you guys really saved me. I will always recommen
... Read more
d you all to everyone that I know. Your system works Great! Thanks Part Select!
Read less
Was this helpful?
Thank you for voting!
pump leaking, washer would not spin right
0 of 2 people
found this instruction helpful.
-
Jim from Lincoln, DE
- Really Easy
- Less than 15 mins
-
Pliers, Socket set
I got the part the very next day, very easy to replace. Replaced the belt as well. Parts Select is the best. Vert straight forward repair.
Was this helpful?
Thank you for voting!
belt was shredded
0 of 2 people
found this instruction helpful.
-
Eric from Atascadero, CA
- Really Easy
- Less than 15 mins
I turned washer over, took off old shredded belt. One of the pulleys is spring loaded so I just held it in as i looped the new belt on. Easiest repair I have made on a washer!
Was this helpful?
Thank you for voting!
Worn bearings on pump, awful screeching noise
0 of 2 people
found this instruction helpful.
-
jim from pasadena, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Unplug. Open the front panel (2 clips, 2 hex head metal screws), remove the two hose clamps and hoses from the pump, remove 3 hex head screws holding the pump...bingo.. in with the new pump, hoses and panel go back....put the drive belt back on...the wife is back in buisness.. Note to all husbands out there, mess up on a few loads of lau
... Read more
ndry (mix red with white and her unmentionables turn a hideous pink) and you never have to do laundry again !!!!
Tip to all, if you have a wet-vac, attached it to the discharge hose of the washer to remove the standing water in the pump.
Right part, right price, delivered right on time Thank you Parts Select
Tip to all, if you have a wet-vac, attached it to the discharge hose of the washer to remove the standing water in the pump.
Right part, right price, delivered right on time Thank you Parts Select
Read less
Was this helpful?
Thank you for voting!
washer was going out of balance
0 of 2 people
found this instruction helpful.
-
Loren from Glennallen, AK
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
watched youtube on how to change out the snubber ring. it was quite easy.
Was this helpful?
Thank you for voting!