CW20P8DSC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Wouldn't spin after rince
1 person
found this instruction helpful.
-
joe from LAWRENCEVILLE, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Followed the great instructions on your video
Was this helpful?
Thank you for voting!
crack in tub hose causing washer water to spill on to floor
1 person
found this instruction helpful.
-
Bette from S BARRINGTON, IL
- Easy
- 30 - 60 mins
-
Pliers, Socket set
raised the top of the washer to get at the front panel screws. Removed the front panel. Removed the cracked hose and installed the new one. Reinstalled the front and top panels.
Was this helpful?
Thank you for voting!
Water leak
1 person
found this instruction helpful.
-
Stephen M. from LEWES, DE
- Really Easy
- 30 - 60 mins
-
Socket set
Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks.
Re installed rear access cover and front panel.
Re installed rear access cover and front panel.
Was this helpful?
Thank you for voting!
My 24 year old Maytag performance washer started occasionally not agitating. Eventually it did not agitate at all but would spin.
1 person
found this instruction helpful.
-
Loretta from LEBANON JCT, KY
- Really Easy
- 30 - 60 mins
-
Screw drivers
The lid switch is on the right side top of the washer under the lid. I took a putty knife and found the clips that hold the top of the washer and pushed them to release it. I then lifted it up to fully see the lid switch. I unplugged the washer from the wall socket and took out the 2 screws that holds the lid switch in. Then unplugged the
... Read more
lid switch from its electrical connection and put the new one in its place. Washer is working great so far.
Read less
Was this helpful?
Thank you for voting!
Washer making noise during cycles
1 person
found this instruction helpful.
-
Nat from Baton Rouge, LA
- Really Easy
- 30 - 60 mins
-
Nutdriver
I moved the washer out from the wall. unplugged washer, turned off water. Took off rear plate exposing pump. Disconnected hoses, using dry/wet vac to catch water. Took out three screws holding pump to base of washer and removed pump, belt slipped right off. Set new pump in place and put in screws. Connected hoses, put rear plate back on.
... Read more
Tilted washer back and installed belt on pulleys and motor. Turned on water, plugged in washer, started to wash clothes. Washer works fine and QUIET. I have yet to find the model number on my Maytag washer. I ordered the pump by sight (good pics).
Read less
Was this helpful?
Thank you for voting!
pulley was scraping bottom of pump
1 person
found this instruction helpful.
-
Brian from Granbury, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
First , I unlocked top cover and propped; removed front cover. tilted machine back propping front. pump is at lower right corner, removed both hoses, removed belt and three screws. reversed order completing job. You will have some water leakage removing hoses.
Was this helpful?
Thank you for voting!
Loud grinding noise when I ran the washing machine
1 person
found this instruction helpful.
-
Eman from Wood Dale, IL
- Easy
- 30 - 60 mins
-
Pliers, Socket set
It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was s
... Read more
tiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00
Read less
Was this helpful?
Thank you for voting!
Water leak
2 of 4 people
found this instruction helpful.
-
Joe from Clearfield, PA
- Really Easy
- 15 - 30 mins
-
Socket set
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
Was this helpful?
Thank you for voting!
Whasher would not drain
1 person
found this instruction helpful.
-
Robert E from Katy, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Used a water hose to syfen out the water. Placed hose in the tub. Turned outside facet to fill hose. Undid hose outside and allowed to drain. Pulled pump. Order online ( Delv fast 2 days ) .Replaced pump . Works great . Good luck with yours.
Was this helpful?
Thank you for voting!
washing machine squeaked on the spin cycle
1 person
found this instruction helpful.
-
Jeffrey from Wabash, IN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!
Was this helpful?
Thank you for voting!
The water pump went out
1 person
found this instruction helpful.
-
felicia from Broken Arrow, OK
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel t
... Read more
hat you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.
Read less
Was this helpful?
Thank you for voting!
Problem manifested as a loud squealing/grinding noise during all cycles.
1 person
found this instruction helpful.
-
Michael from Atlanta, GA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Disconnected both power and hot and cold input water lines. Laid the washer on its front side for access to the bottom. Removed the small access panel from the back of the machine to remove the metal screws holding the pump in place. Removed the single drive belt. New pump installed easily, replaced the belt and access panel. Reconne
... Read more
cted the power and water hoses and everything worked fine.
Read less
Was this helpful?
Thank you for voting!
Plastic Lid Hinge was broken
2 of 4 people
found this instruction helpful.
-
Thomas from Coral Springs, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Changing the hinge was not difficult, but here's a hint: the top of the washer raises up if you pry it with a big screwdriver- be sure to wrap the screwdriver in a cloth so as not to scratch the appliance. Doing it this way makes it easy to access the retaining screws. You can push the wash tub to one side and reach the screws from undern
... Read more
eath, but they're a tight fit and doing it that way is difficult. Overall a pretty easy repair and I'm only moderately handy.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water removal pump stopped working.
1 person
found this instruction helpful.
-
Timothy from Palmdale, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Removed lower rear panel by removing 8 screws. Then I removed the two hoses that are attached to the pump by removing the hose clamps with a pair of plyers. The three hex head screws that anchor the pump to the base of the washer unit were removed and the pump came right out. To put the new pump in I just slipped the pump through the hol
... Read more
e at the bottom of the washer and attached the belt onto the pulley. Then reversed the installation process. The washer had to be tipped forward slightly for this process and blocked (approx. 8 in.) to allow access to pulley. Very easy install, no help needed. Washer must be empty and preferable dry when task is done or water will be everywhere.
Read less
Was this helpful?
Thank you for voting!
loud grinding sound then washer would shut down then there was water all over
1 person
found this instruction helpful.
-
marilisa from naples, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set
first removed panel from rear of washer removed hoses and drained water in them, removed the 3 screws and removed the belt then removed the pump. Replaced with new one and put back screws,hoses and belt. walaaa.... it works like new!!!!
Was this helpful?
Thank you for voting!