EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW20P8ASC Crosley Washer - Instructions

All Instructions for the CW20P8ASC
106 - 120 of 289

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
machine was starting to make noises when spinning
1 of 2 people found this instruction helpful.
  • Virginia from Rockford, IL
  • Really Easy
  • Less than 15 mins
My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.
Was this helpful?
Thank you for voting!
water not draining
1 of 2 people found this instruction helpful.
  • FRANK from CHULA VISTA, CA
  • Really Easy
  • 15 - 30 mins
  • Socket set
changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks
Was this helpful?
Thank you for voting!
Started making loud screeching noise(bad Bearing)
1 of 2 people found this instruction helpful.
  • Michele from Lebanon, PA
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.
Was this helpful?
Thank you for voting!
noisy out of balance during spin cycles
1 of 2 people found this instruction helpful.
  • Ronald from Wading River, NY
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Socket set
I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise !
Was this helpful?
Thank you for voting!
Washer making loud noise and tub off balance
1 of 2 people found this instruction helpful.
  • Hollee from Rancho Mirage, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I followed Gary from Sioux City IA instructions. Very well explained.
Was this helpful?
Thank you for voting!
discharge pulley assembly bearing going out on it.
1 of 2 people found this instruction helpful.
  • Milton from bartlett, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and d id a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.
Was this helpful?
Thank you for voting!
Washing machine began making a screeching noise but only during the spin cycle - when it was emptying the water from the tub. After a few uses the machine just stopped working.
1 of 2 people found this instruction helpful.
  • Patricia from Modesto, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
The pump was easy enough to replace. Access panel in the back and 3 screws and it was off and back on in less than 20 minutes. It was putting the belt on that gave me the most trouble even though one of the pulleys moved to allow for easy replacement it did not move enough. It took me another 30 minutes just to get the belt on. I fina lly decided to place the belt on the two smaller pulleys and save the larger one for last and it went on with no trouble at all. Learn from my error =]
Was this helpful?
Thank you for voting!
Made noise during washing and rinse cycle
1 of 2 people found this instruction helpful.
  • Jose from Elizabeth, NJ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
It was easy to replace the water pump
Was this helpful?
Thank you for voting!
Water leaking on floor
1 of 3 people found this instruction helpful.
  • ALISON from MARTINEZ, GA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Removed back access cover and lift top cover looking for leak. Initially thought it may have been the pump housing. I filled some water into the tub and I flexed the hose between the tub and the pump and water sprayed out. It had cracked in about 3 small places (water is present in the hose anytime water is in the tub) Ordered and replace d hose. Also order drive belt and replaced as a preventive maintenance item.
Was this helpful?
Thank you for voting!
Tub cracked while replacing snubber
1 of 3 people found this instruction helpful.
  • Nicholas from King of Prussia, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Remove tub assembly per snubber replacement procedure.
Place tub assembly on top of a milk crate open-side up.
Support tub assembly on milk crate with 2x4's to protect pully from damage.
Remove agitator from tub assembly.
Press down on tub assembly cap, release tabs and remove tub assembly cap.
Remove inner tub from tub assembly.
Mark tub frame with location of outer tub air bell for ease of reassembly.
Remove outer tub from transmission assembly.
Replace inner tub gasket
Replace outer tub gasket

Problem encountered was that the replacement tub had a defective air bell. The washer consequently did not detect fill level and subsequently overflowed flooding the laundry room. The bell looked ok visually. Blowing into the air tube while plugging the inside hole with a finger revealed a pinhole leak in one corner of the PP weld. PartSelect was prompt with replacement, but the job had to be redone in its entirety.

Always test the air bell before installing an outer tub.
Was this helpful?
Thank you for voting!
machine woulden't spin properly
1 of 3 people found this instruction helpful.
  • Richard from Ponte Vedra Bch, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
diagnosed a loose belt-- ordered and received same -- installed and set to proper tension that was simple.
Was this helpful?
Thank you for voting!
Washer was leaking water.
1 of 3 people found this instruction helpful.
  • Steven from Atlanta, GA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Socket set, Wrench (Adjustable)
Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.
Was this helpful?
Thank you for voting!
Pump was making a grinding noise.
1 of 3 people found this instruction helpful.
  • Daniel from Hinsdale, IL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.
Was this helpful?
Thank you for voting!
leaking water on the floor-Hose had hole in it
1 of 3 people found this instruction helpful.
  • Mark from Katy, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Remove the metal plate in back of the washer that 3 screws. I use a vise-grips to remove the two clamps.One on other the tub side and the other the pump side. Pull the old hose off the tub side and the pump side.Use the old clamps to put the new hose on.
Was this helpful?
Thank you for voting!
Washer making loud noise when water pump operating, still worked but made very loud noise
0 of 1 people found this instruction helpful.
  • Buddy from Ogden, UT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
I ordered the replacement pump assembly (water pump)for my Atlantis model maytag washer, removed the old one, installed the new one and works like a charm. The only difficulty I had was trying to figure out how to remove the cover on the front of the washer, to remove the clips, it slid side to side instead of popping out, found the inst ructions on-line, NO instructions came with the pump but if you have any common sense when it comes to repairs it was easy to remove and install the new part.
Was this helpful?
Thank you for voting!
All Instructions for the CW20P8ASC
106 - 120 of 289