CW20P6H Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer was leaking water.
1 of 3 people
found this instruction helpful.
-
Steven from Atlanta, GA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.
Was this helpful?
Thank you for voting!
leaking water on the floor-Hose had hole in it
1 of 3 people
found this instruction helpful.
-
Mark from Katy, TX
- Easy
- 15 - 30 mins
-
Screw drivers
Remove the metal plate in back of the washer that 3 screws. I use a vise-grips to remove the two clamps.One on other the tub side and the other the pump side. Pull the old hose off the tub side and the pump side.Use the old clamps to put the new hose on.
Was this helpful?
Thank you for voting!
machine woulden't spin properly
1 of 3 people
found this instruction helpful.
-
Richard from Ponte Vedra Bch, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
diagnosed a loose belt-- ordered and received same -- installed and set to proper tension that was simple.
Was this helpful?
Thank you for voting!
Bearings in mechanical pump seized.
0 of 1 people
found this instruction helpful.
-
Scott from Idaho Falls, ID
- Easy
- Less than 15 mins
-
Pliers, Socket set
Unbolt old pump with three bolt from top of pump inside the washer. Use needlenose pliers to remove intake and output hoses from old pump. Remove belt from pulley under washer. Reverse procedure to install. I was worried because there were two pumps listed for this model number, one being $95 and the other being $40. I bought the cheaper
... Read more
one and prayed. It worked just fine. Fixed a $500 washer that was on it's way to the dump and made $100 in the process!
Read less
Was this helpful?
Thank you for voting!
Washing machine had difficulty in spine cycle
0 of 1 people
found this instruction helpful.
-
Stephanie from Ticonderoga, NY
- Really Easy
- Less than 15 mins
Unplugged everything, disconnected hoses, took belt off and put new one on.
Was this helpful?
Thank you for voting!
worn drive belt
0 of 1 people
found this instruction helpful.
-
James from Shortsville, NY
- Really Easy
- Less than 15 mins
tilted the machine forward, worked off the old belt and put the new belt back on. no tools required, done in less than 5 minutes.
Was this helpful?
Thank you for voting!
Washer Machine just shut down.
0 of 1 people
found this instruction helpful.
-
Patrick from Indianola, MS
- Really Easy
- Less than 15 mins
All i had to do was pull the washer machine from the wall and lean it back as far as i could and get under it and place the (DRIVE BELT) on the two smallest pulley then put the belt on the large pulley and my work was done it was very simple and easy.......
Was this helpful?
Thank you for voting!
Made an awful sqealing noise and did not spin the water out all the way
0 of 1 people
found this instruction helpful.
-
Deborah from Baltimore, MD
- Really Easy
- Less than 15 mins
-
Socket set
Leaned the washer back and propped it up and changed the belt. This is the first time ever repairing an appliance. I feel very good about myself as I am 49 yrs old and did not have to call a repairman for this.
Was this helpful?
Thank you for voting!
Washer would not go into spin cycle.
0 of 1 people
found this instruction helpful.
-
Jack from Scottdale, PA
- Really Easy
- Less than 15 mins
I pulled the washer away from the wall so that I could lean it back at an angle. I removed the old belt and put the new one on. I started with the smaller pulley first and put the belt into the groove. Next I went to the next larger pulley and did the same thing. Then I went to the largest pulley and started to put the belt into the groov
... Read more
e and started turning the pulley by hand. The belt went right on.
Read less
Was this helpful?
Thank you for voting!
drive belt broke
0 of 1 people
found this instruction helpful.
-
Gerard from Keansburg, NJ
- Really Easy
- Less than 15 mins
pulled out the washing machine that was the hard part, tilted it back checked too make sure everything spun by hand just to see if that was reason for the belt to snap but everything spun by hand nice and smoothly poped on the drive belt and everything works fine back in business.
Was this helpful?
Thank you for voting!
Under belt was used and ready to let go..
0 of 1 people
found this instruction helpful.
-
Melanie from Tamarac, FL
- Really Easy
- Less than 15 mins
First I am a woman and was able to do it, and if I can do it anyone should be able to do this. The service call alone was 75.00, and the belt was 23.00 with shipping. First we tilted the washer at a 45 degree angle and I removed the belt, and just rolled the newer one on the track. That was it and I was done. My washer now purrs like a ki
... Read more
tten love it. And Part Select sent out my part and I recieved it next day, thank you for wonderful service that kind of service is hard to find. <3
Read less
Was this helpful?
Thank you for voting!
no cold water
1 of 4 people
found this instruction helpful.
-
juan from moreno valley, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
I pulled the top ofthe washer up, I disconnected the cold and hot water hoses, took the 2 bolts off with a socket and pulled the water valve from the top. I used the pliers to take the pressure ring off and pulled over flow hose off. I pulled the four wires off with pliers. Put the new water valve in reverse order...easy.
Was this helpful?
Thank you for voting!
loud sqeaking noise, burnt rubber smell, motor siezing up
0 of 1 people
found this instruction helpful.
-
Ricky from Colorado Springs, CO
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Unplugged electrical plug. Disconnected water and drain hoses. Turned washer on front side. Removed old belt from bottom of washer. Removed pump access panel. Removed old pump. Installed new pump. Torqued pump mounting screws 1/4 turn with socket wrench. Installed new belt. Put on pump access panel. Hand tested motion of belt and pulleys
... Read more
for smooth travel. Put drain hose on. Turned washer in the upright position. Reconnected water hoses. Washer works like new.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
loud noise while washing, spinning and draining
0 of 1 people
found this instruction helpful.
-
Julia from Columbia, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
took off back small metal panel, tilted washer front side down, easy to put into place after removing old part
Was this helpful?
Thank you for voting!
Squealing Belt In All Cycles
0 of 1 people
found this instruction helpful.
-
TERRY E from TUCSON, AZ
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Because I live alone, the washer is very heavy so I just used some sliding robots under the legs of washer so I could slide it out from the wall by myslef after removing the small plate in the back to accfess the water pump I used the nut driver to remove the 3 screws holding the pump in place, but I used the pliers to remove the 2 water
... Read more
hoses first then I mounted the water pump back into place, installed both hoses again then I tilted it back against the wall while re installing the belt then I pushed it back against the wall and removed the sliders so I could make sure it was back level this was a very easy repair even if you never fixed any thing before the belt replacement was even more simple to replace because the motor is springloaded so you just had to pull on it enough to remove it from the pulleys
Read less
Was this helpful?
Thank you for voting!