EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW20P6H Crosley Washer - Instructions

All Instructions for the CW20P6H
61 - 75 of 295

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Pump needed replacing
2 of 3 people found this instruction helpful.
  • Thomas from Los Alamos, NM
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Removed the front panel to get some light in to the machine. Removed the two hoses connecting the pump to the drain and tub. Removed the three screws holding the old pump in place. Did the reverse to install.
This was a piece of cake.
Thanks for having the parts needed to do this job.
Tom
Was this helpful?
Thank you for voting!
Water leaking when washer was filling with water.
3 of 6 people found this instruction helpful.
  • Colleen from Glenflora, WI
  • Difficult
  • 15 - 30 mins
  • Pliers
Took off the back plate. Looked to see where it was leaking. Squeezed the clamps on top and bottom to remove from hose and pull hose out.
Was this helpful?
Thank you for voting!
water leaking under washer
3 of 6 people found this instruction helpful.
  • paul from akron, OH
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
removed rear acess panel and used pliers to remove leaking hose then reinstalled new hose..
Was this helpful?
Thank you for voting!
rinse cycle was not expelling the water
2 of 3 people found this instruction helpful.
  • bert from coudersport, PA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
remmoved the screws on the back that hold the panel on. removed the two hoses attched to the pump. removed three screws and pulled the pump out. spun the pulley and noticed no movement inside. looked closer at the pulley to notice it was broken. ordered new pulley online. received quickly. new part fit exacttly right. put three sc rews back in. hooked two hoses back up. put belt on pulley. plugged in and worked great.
Was this helpful?
Thank you for voting!
tub overflowed
2 of 3 people found this instruction helpful.
  • Ellen from Wilcox, AZ
  • A Bit Difficult
  • 1- 2 hours
Back of this washer did not remove, so we had to go in through the top--more restricting space. As you remove the old electrical metal contacts (two each of white and red), pay close attention to where they connect properly. Best to mark them so as not to confuse how to place new contacts. Also, we disconnected a white plastic hose on opposite side of top which determines load size and amount of water, so be sure to look for this.
Was this helpful?
Thank you for voting!
No belt and no motor gear
2 of 3 people found this instruction helpful.
  • Matt from Hoboken, NJ
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Wrench set
Pop the top of the washer and use the nutdriver to remove the two screws holding the frontpanel on. Use the nutdriver for two more screws holding the plastic motor cover on. Use nutdriver for the two BIG screws holding the motorplate to the washer frame. After this, I literally beat/chiped/sawed the old motor geat off. Once that was d one, I put the new one on; had to use a hammer to knock it all the way on (try not to damage the clips). Reassemble everything. Flip washer over and place bet around two smaller gears. Rotate main tub gear to feed belt on. Make sure you use the nutdriver to loosen/tighten the motor positioner screws in the slots if things aren't working here.
The only really hard thing was taking the old motor gear off.
Was this helpful?
Thank you for voting!
The washer was jumping all over the place and leaking water during the spin cycle
4 of 9 people found this instruction helpful.
  • Elmer from Fort Campbell, KY
  • Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
I took out the agitator first, then I took out the inner tub, next I took out the outer tub, and last I took out the transmission assembly. After replacing the snubber I put the transmission assembly back on, then the new outer tub and next the inner tub. Last I put the agitator back on.
Was this helpful?
Thank you for voting!
Little Cold Water Flow
2 of 3 people found this instruction helpful.
  • David from Lexington, KY
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set, Wrench (Adjustable)
Unplug power cord; turn off hot and cold water supply; remove water hoses from machine; open top of machine by prying lid open; remove two hex screws holding water inlet valve in place; remove hose from top of old water inlet valve; remove 4 wires; connect bottom set of wires (red and white) to new water inlet valve; reinstall water hose to top of new water inlet valve; install new water inlet valve onto machine using same hex screws; connect remiaining red and white wires; install hot and cold water hoses to machine; turn on water supply valves at wall; reconnect wall plug; turn water type selector to cold, pull out timer and watched the water flow full-force for the first time in 2 years! Have wife give you a hug for saving cost of new washing machine!
Was this helpful?
Thank you for voting!
Noisy on spin cycle
2 of 3 people found this instruction helpful.
  • William B from STURGIS, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos
Was this helpful?
Thank you for voting!
Washing machine was noisy (metal on metal) after the tub filled up and the motor engaged for the wash cycle.
2 of 3 people found this instruction helpful.
  • GARY from Montvale, NJ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I unplugged the machine, tipped it back slightly and rested in on a gallon paint can. I inspected the under side and manually advanced the fan belt to hear if I could hear the noise at the water pump. The pump pulley and shaft was worn and there were metal shavins (small) on surface of pulley.

Then I removed the belt from the p ulley, rested the machine back to normal position, removed front panel (two sheet metal screws on inside top), removed the water pump hoses (htere is water int he hose & pump assembly so you will get some water on floor.

Then I removed the pump and ordered a new one. The installation was the reverse, machine works like new and the washer tub spins better than ever during the final rinse and spin, since the worn water pump was binding and stressing the machine.

Thanks to Part Select - Your website is awesome and your service instructions and user advice gave me the confidence to do the repair myself. I saved $150 - $250 for the repair.
Was this helpful?
Thank you for voting!
Water dripped into washer even when off
1 person found this instruction helpful.
  • Larry from Mansfield, MA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Hardest part was figuring out how to get to the water valve. Turned out that the way in was from the top. All I had to do is remove two screws at the back of the top panel, and then unclip the front edge of the top panel (use a thin screwdriver to press in on the clips from the front of the machine). From there, it was easy to reach dow n inside and remove/replace the valve.
Was this helpful?
Thank you for voting!
Loud grinding noise when I ran the washing machine
1 person found this instruction helpful.
  • Eman from Wood Dale, IL
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set
It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was s tiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00
Was this helpful?
Thank you for voting!
pulley was scraping bottom of pump
1 person found this instruction helpful.
  • Brian from Granbury, TX
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
First , I unlocked top cover and propped; removed front cover. tilted machine back propping front. pump is at lower right corner, removed both hoses, removed belt and three screws. reversed order completing job. You will have some water leakage removing hoses.
Was this helpful?
Thank you for voting!
Washer making noise during cycles
1 person found this instruction helpful.
  • Nat from Baton Rouge, LA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I moved the washer out from the wall. unplugged washer, turned off water. Took off rear plate exposing pump. Disconnected hoses, using dry/wet vac to catch water. Took out three screws holding pump to base of washer and removed pump, belt slipped right off. Set new pump in place and put in screws. Connected hoses, put rear plate back on. Tilted washer back and installed belt on pulleys and motor. Turned on water, plugged in washer, started to wash clothes. Washer works fine and QUIET. I have yet to find the model number on my Maytag washer. I ordered the pump by sight (good pics).
Was this helpful?
Thank you for voting!
Noise
1 person found this instruction helpful.
  • Marylou from Old Forge, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Wrench (Adjustable)
I changed the piece easily
Was this helpful?
Thank you for voting!
All Instructions for the CW20P6H
61 - 75 of 295