EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW20P5WC Crosley Washer - Instructions

All Instructions for the CW20P5WC
106 - 120 of 386

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water removal pump stopped working.
1 person found this instruction helpful.
  • Timothy from Palmdale, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Removed lower rear panel by removing 8 screws. Then I removed the two hoses that are attached to the pump by removing the hose clamps with a pair of plyers. The three hex head screws that anchor the pump to the base of the washer unit were removed and the pump came right out. To put the new pump in I just slipped the pump through the hol e at the bottom of the washer and attached the belt onto the pulley. Then reversed the installation process. The washer had to be tipped forward slightly for this process and blocked (approx. 8 in.) to allow access to pulley. Very easy install, no help needed. Washer must be empty and preferable dry when task is done or water will be everywhere.
Was this helpful?
Thank you for voting!
end broken on the hinge
1 person found this instruction helpful.
  • James from Louisville, KY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
used putty knife to to raise the top, took out two screws, replaced parts , then closed the top.
Was this helpful?
Thank you for voting!
Washer had bad water pump
1 person found this instruction helpful.
  • Edwin from Eagar,, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Removed access panel to expose pump, removed drive belt, and old pump, repeated the avove steps in reverse order, tested for leaks and proper operation.
Was this helpful?
Thank you for voting!
Loud grinding noise when I ran the washing machine
1 person found this instruction helpful.
  • Eman from Wood Dale, IL
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set
It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was s tiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00
Was this helpful?
Thank you for voting!
Water leak
2 of 4 people found this instruction helpful.
  • Joe from Clearfield, PA
  • Really Easy
  • 15 - 30 mins
  • Socket set
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
Was this helpful?
Thank you for voting!
Water leaked from bottom of Washing Machine.
1 person found this instruction helpful.
  • Brandon from Lake Elsinore, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done
Was this helpful?
Thank you for voting!
Drain pump making load screeching noise
1 person found this instruction helpful.
  • Danny from Fort Worth, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nut driver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
Was this helpful?
Thank you for voting!
broken lid hinge
2 of 4 people found this instruction helpful.
  • loyce from charleston, SC
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
I had my boyfriend take the lid off ,then he took off the two old hinges,one was broken,and the he replaced both lid hinges,daving the good one. it was very simple and quick for him.

Iwill use your service again,thanks.
Loyce Floyd
Was this helpful?
Thank you for voting!
washing machine squeaked on the spin cycle
1 person found this instruction helpful.
  • Jeffrey from Wabash, IN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!
Was this helpful?
Thank you for voting!
The water pump went out
1 person found this instruction helpful.
  • felicia from Broken Arrow, OK
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel t hat you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.
Was this helpful?
Thank you for voting!
Problem manifested as a loud squealing/grinding noise during all cycles.
1 person found this instruction helpful.
  • Michael from Atlanta, GA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Disconnected both power and hot and cold input water lines. Laid the washer on its front side for access to the bottom. Removed the small access panel from the back of the machine to remove the metal screws holding the pump in place. Removed the single drive belt. New pump installed easily, replaced the belt and access panel. Reconne cted the power and water hoses and everything worked fine.
Was this helpful?
Thank you for voting!
Plastic Lid Hinge was broken
2 of 4 people found this instruction helpful.
  • Thomas from Coral Springs, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Changing the hinge was not difficult, but here's a hint: the top of the washer raises up if you pry it with a big screwdriver- be sure to wrap the screwdriver in a cloth so as not to scratch the appliance. Doing it this way makes it easy to access the retaining screws. You can push the wash tub to one side and reach the screws from undern eath, but they're a tight fit and doing it that way is difficult. Overall a pretty easy repair and I'm only moderately handy.
Was this helpful?
Thank you for voting!
Broken left Hinge Pin on Lid
1 person found this instruction helpful.
  • Hing from Toms River, NJ
  • Really Easy
  • Less than 15 mins
1. Remove 1 screw holding each of 2 Hinges - use T15 driver. 2. Push tub to one side to get access to each screw from underside. 3. remove & replace broken Hinge Pin from Lid with T15 driver. 4. Drive broken pin out of the Hinge with a punch & hammer. 5. Install new Hinge Pin to Lid. 6. Add a little Vaseline to Hinge Pin & slide Hin ge Pin into Hinge. 7. Line up Hinges to holes & re-install both Hinges with Lid. Have somebody help hold the Lid in a slight angle will make re-installation easier.
Was this helpful?
Thank you for voting!
Broken belt needed to be replaced.
1 person found this instruction helpful.
  • Niels from Hopewell Junction, NY
  • Easy
  • Less than 15 mins
  • Socket set, Wrench (Adjustable)
Replacing a belt on a washing machine is a pretty easy process, depending slightly on how easy it is to access the belt. On our Maytag, the belt can be accessed directly underneith the washing machine. So, I lifted the front of the machine and put a few blocks of scrap wood under the legs to hold up the front of the machine. Once that was done, there was nothing else that needed to be removed to access the pullies that the belt had to go around. The motor itself is generally adjustable to allow the belt to be changed. So, I first wrapped the belt around the largest one that spins the washin machine tub, and then wrapped it around the one that spins the water pump. Finally, I loosened the bolt on the motor to allow it to move, wrapped the belt around the motor, pulled the motor back to tighten up the belt, and tightened the bolt that holds the motor in place. It's a pretty straight forward repair that narly anyone could do thmselves.
Was this helpful?
Thank you for voting!
Locked up the machine.
1 person found this instruction helpful.
  • Mitchell B. from Moreno Valley, CA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the machine up . Worked perfect.











the
Was this helpful?
Thank you for voting!
All Instructions for the CW20P5WC
106 - 120 of 386