CW20P4W Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Activator device broken off
1 person
found this instruction helpful.
-
Sonya from VAIL, AZ
- Very Easy
- Less than 15 mins
-
Screw drivers
Easy repair - with the use of a phillips screwdriver, simply remove the old device and replace with the new
Was this helpful?
Thank you for voting!
Worn belt
1 person
found this instruction helpful.
-
Richard from OXFORD, NY
- Really Easy
- Less than 15 mins
Rolled the old one off and rolled the new one on.
Was this helpful?
Thank you for voting!
old belt broke and fell off
2 of 4 people
found this instruction helpful.
-
Tim from New London, OH
- Really Easy
- Less than 15 mins
tipped the washer back, laid on the floor, and wrapped new belt around 3 pulleys. everything works as before.
Was this helpful?
Thank you for voting!
Had the screeching noise for a few days and kept using it until it finally didn't do anything. From youtube i was able to diagnose using other peoples experiences and discovered the part i need by looking at the pictures from the model #.
1 person
found this instruction helpful.
-
Rita from Rodarte, NM
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I had my 12 year old son climb to the back and he took off all the screws necessary in the back and took the part completely off. We ordered the part and waited for it to come in. We replaced the part, the screws and honestly, the only thing we had trouble with was replacing the small cover where the hoses stick out of the washer. Was
... Read more
an easy efficient experience that may have saved me $300.00+ dollars. Thanks to my 12 year old son we got her fixed up. The washer works like brand new.
Read less
Was this helpful?
Thank you for voting!
Started making loud screeching noise(bad Bearing)
1 of 2 people
found this instruction helpful.
-
Michele from Lebanon, PA
- Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.
Was this helpful?
Thank you for voting!
Made noise on spin cycle
1 of 2 people
found this instruction helpful.
-
Les from Moneta, VA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.
Other Parts Used:
Was this helpful?
Thank you for voting!
machine was starting to make noises when spinning
1 of 2 people
found this instruction helpful.
-
Virginia from Rockford, IL
- Really Easy
- Less than 15 mins
My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to
... Read more
clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.
Read less
Was this helpful?
Thank you for voting!
Old hot water inlet hose had budge at both ends.
2 of 5 people
found this instruction helpful.
-
Jimmy from MEMPHIS, TN
- Very Easy
- Less than 15 mins
-
Pliers
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this helpful?
Thank you for voting!
water not draining
1 of 2 people
found this instruction helpful.
-
FRANK from CHULA VISTA, CA
- Really Easy
- 15 - 30 mins
-
Socket set
changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks
Was this helpful?
Thank you for voting!
Lid hinges wear out, causing lid to slam as you are trying to put clothes in or take them out.
1 of 2 people
found this instruction helpful.
-
Jan from Challis, ID
- Easy
- Less than 15 mins
-
Screw drivers
Lift the top of the washer so you can access the screws that hold the hinges. Replace the hinges,and close the washer top. This is the sescond time we have had to replace the hinges.
This lid and hinges are very poorly designed. Instead of opening to the side, it opens straight back. That means when the hinges wear out (an ... Read more d they do because they are plastic), you have to push the lid all the way back to stay open. When you push it all the way back, it hits the control knob and turns off the water.
If you are like me, I like to turn the water on and add the soap so it can dissolve before I add the clothes. It is really irritating when you open the lid and the only way for it to stay open is to push it all the way back and the water shuts off. And if you don't push it all the way back, it slams and scares the bejeebers out of you or slams on your fingers.
This lid and hinges are very poorly designed. Instead of opening to the side, it opens straight back. That means when the hinges wear out (an ... Read more d they do because they are plastic), you have to push the lid all the way back to stay open. When you push it all the way back, it hits the control knob and turns off the water.
If you are like me, I like to turn the water on and add the soap so it can dissolve before I add the clothes. It is really irritating when you open the lid and the only way for it to stay open is to push it all the way back and the water shuts off. And if you don't push it all the way back, it slams and scares the bejeebers out of you or slams on your fingers.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer wouldn't spin because the switch on the lid broke
2 of 5 people
found this instruction helpful.
-
Rachelle from Eagle Mountain, UT
- Really Easy
- Less than 15 mins
-
Screw drivers
I unscrewed the old lid switch and screwed on the new switch in seriously 2 minutes!
Was this helpful?
Thank you for voting!
broken lid hinge
1 of 2 people
found this instruction helpful.
-
dorris from slaughters, KY
- Easy
- 15 - 30 mins
-
Screw drivers
short drive, 90 degree, "star" driver. push tub to side and back to reach lower part of old hinge, remove single screw. (careful not to drop it into the "mechanics" of the tub.) repeat for the other side. remove parts from lid. reassemble new parts onto lid, along with lower hinge parts. secure the lower hinge to door part(s) with maski
... Read more
ng tape to hold in place. hold lid in place over lower hinge screw holes and start screws by hand. snug up the screws and your done! the 'STAR" screws may be relpaced with similar "phillips" so you wont have to scrounge for a "star" driver the next time.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water pump replacement
1 of 2 people
found this instruction helpful.
-
Lon from Morton Grove, IL
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Socket set
Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process ... Read more to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process ... Read more to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
Read less
Was this helpful?
Thank you for voting!
Broken Hinge Pin
1 of 2 people
found this instruction helpful.
-
John from Dover, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I followed the feed back in the forum from a previous repair. I popped open the top of the Washing and propped it open @ approx. 70 degrees,moved the Tub out of the way and used a small Phillips Scwdrvr to remove the broken part, installing the new parts was a snap, I took the time to use a Q-Tip and petroleum jelly to coat the pin and hi
... Read more
nge making it easier and less binding when opening the lid.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Made noise during washing and rinse cycle
1 of 2 people
found this instruction helpful.
-
Jose from Elizabeth, NJ
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
It was easy to replace the water pump
Other Parts Used:
Was this helpful?
Thank you for voting!