CW18T2A Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing machine began making a screeching noise but only during the spin cycle - when it was emptying the water from the tub. After a few uses the machine just stopped working.
1 of 2 people
found this instruction helpful.
-
Patricia from Modesto, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
The pump was easy enough to replace. Access panel in the back and 3 screws and it was off and back on in less than 20 minutes. It was putting the belt on that gave me the most trouble even though one of the pulleys moved to allow for easy replacement it did not move enough. It took me another 30 minutes just to get the belt on. I fina
... Read more
lly decided to place the belt on the two smaller pulleys and save the larger one for last and it went on with no trouble at all. Learn from my error =]
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
discharge pulley assembly bearing going out on it.
1 of 2 people
found this instruction helpful.
-
Milton from bartlett, IL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and d
... Read more
id a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.
Read less
Was this helpful?
Thank you for voting!
Water leaking on floor
1 of 3 people
found this instruction helpful.
-
ALISON from MARTINEZ, GA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed back access cover and lift top cover looking for leak. Initially thought it may have been the pump housing. I filled some water into the tub and I flexed the hose between the tub and the pump and water sprayed out. It had cracked in about 3 small places (water is present in the hose anytime water is in the tub) Ordered and replace
... Read more
d hose. Also order drive belt and replaced as a preventive maintenance item.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Tub cracked while replacing snubber
1 of 3 people
found this instruction helpful.
-
Nicholas from King of Prussia, PA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Remove tub assembly per snubber replacement procedure.
Place tub assembly on top of a milk crate open-side up.
Support tub assembly on milk crate with 2x4's to protect pully from damage.
Remove agitator from tub assembly.
Press down on tub assembly cap, release tabs and remove tub assembly cap.
Remove inner tub ... Read more from tub assembly.
Mark tub frame with location of outer tub air bell for ease of reassembly.
Remove outer tub from transmission assembly.
Replace inner tub gasket
Replace outer tub gasket
Problem encountered was that the replacement tub had a defective air bell. The washer consequently did not detect fill level and subsequently overflowed flooding the laundry room. The bell looked ok visually. Blowing into the air tube while plugging the inside hole with a finger revealed a pinhole leak in one corner of the PP weld. PartSelect was prompt with replacement, but the job had to be redone in its entirety.
Always test the air bell before installing an outer tub.
Place tub assembly on top of a milk crate open-side up.
Support tub assembly on milk crate with 2x4's to protect pully from damage.
Remove agitator from tub assembly.
Press down on tub assembly cap, release tabs and remove tub assembly cap.
Remove inner tub ... Read more from tub assembly.
Mark tub frame with location of outer tub air bell for ease of reassembly.
Remove outer tub from transmission assembly.
Replace inner tub gasket
Replace outer tub gasket
Problem encountered was that the replacement tub had a defective air bell. The washer consequently did not detect fill level and subsequently overflowed flooding the laundry room. The bell looked ok visually. Blowing into the air tube while plugging the inside hole with a finger revealed a pinhole leak in one corner of the PP weld. PartSelect was prompt with replacement, but the job had to be redone in its entirety.
Always test the air bell before installing an outer tub.
Read less
Was this helpful?
Thank you for voting!
machine woulden't spin properly
1 of 3 people
found this instruction helpful.
-
Richard from Ponte Vedra Bch, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
diagnosed a loose belt-- ordered and received same -- installed and set to proper tension that was simple.
Was this helpful?
Thank you for voting!
Washer was leaking water.
1 of 3 people
found this instruction helpful.
-
Steven from Atlanta, GA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.
Was this helpful?
Thank you for voting!
Pump was making a grinding noise.
1 of 3 people
found this instruction helpful.
-
Daniel from Hinsdale, IL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I
... Read more
reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.
Read less
Was this helpful?
Thank you for voting!
leaking water on the floor-Hose had hole in it
1 of 3 people
found this instruction helpful.
-
Mark from Katy, TX
- Easy
- 15 - 30 mins
-
Screw drivers
Remove the metal plate in back of the washer that 3 screws. I use a vise-grips to remove the two clamps.One on other the tub side and the other the pump side. Pull the old hose off the tub side and the pump side.Use the old clamps to put the new hose on.
Was this helpful?
Thank you for voting!
no cold water
1 of 4 people
found this instruction helpful.
-
juan from moreno valley, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
I pulled the top ofthe washer up, I disconnected the cold and hot water hoses, took the 2 bolts off with a socket and pulled the water valve from the top. I used the pliers to take the pressure ring off and pulled over flow hose off. I pulled the four wires off with pliers. Put the new water valve in reverse order...easy.
Was this helpful?
Thank you for voting!
loud noise while washing, spinning and draining
0 of 1 people
found this instruction helpful.
-
Julia from Columbia, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
took off back small metal panel, tilted washer front side down, easy to put into place after removing old part
Was this helpful?
Thank you for voting!
Squealing Belt In All Cycles
0 of 1 people
found this instruction helpful.
-
TERRY E from TUCSON, AZ
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Because I live alone, the washer is very heavy so I just used some sliding robots under the legs of washer so I could slide it out from the wall by myslef after removing the small plate in the back to accfess the water pump I used the nut driver to remove the 3 screws holding the pump in place, but I used the pliers to remove the 2 water
... Read more
hoses first then I mounted the water pump back into place, installed both hoses again then I tilted it back against the wall while re installing the belt then I pushed it back against the wall and removed the sliders so I could make sure it was back level this was a very easy repair even if you never fixed any thing before the belt replacement was even more simple to replace because the motor is springloaded so you just had to pull on it enough to remove it from the pulleys
Read less
Was this helpful?
Thank you for voting!
Washer making loud noise when water pump operating, still worked but made very loud noise
0 of 1 people
found this instruction helpful.
-
Buddy from Ogden, UT
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I ordered the replacement pump assembly (water pump)for my Atlantis model maytag washer, removed the old one, installed the new one and works like a charm. The only difficulty I had was trying to figure out how to remove the cover on the front of the washer, to remove the clips, it slid side to side instead of popping out, found the inst
... Read more
ructions on-line, NO instructions came with the pump but if you have any common sense when it comes to repairs it was easy to remove and install the new part.
Read less
Was this helpful?
Thank you for voting!
loud sqeaking noise, burnt rubber smell, motor siezing up
0 of 1 people
found this instruction helpful.
-
Ricky from Colorado Springs, CO
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Unplugged electrical plug. Disconnected water and drain hoses. Turned washer on front side. Removed old belt from bottom of washer. Removed pump access panel. Removed old pump. Installed new pump. Torqued pump mounting screws 1/4 turn with socket wrench. Installed new belt. Put on pump access panel. Hand tested motion of belt and pulleys
... Read more
for smooth travel. Put drain hose on. Turned washer in the upright position. Reconnected water hoses. Washer works like new.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Noisy Pump
2 of 7 people
found this instruction helpful.
-
Frederick from Yuma, AZ
- Really Easy
- 15 - 30 mins
-
Nutdriver
I placed the washer on a couple of work-horses so I could have access to the belt underneath. Then I used my nutdriver to removed the lower back panel. Disconnected both of the hoses, and removed the pump with my nutdrivers. Placed the new pump in place, placed the belt back on the pump's pully, tightened down the pump. I then plugged
... Read more
in the washer and put a little water in the washer to test that everything was working. After confirming that everything worked, I replaced the lower back panel and put the washer back in business. 30 minutes from beginning to end ... and a good time was had by all.
Read less
Was this helpful?
Thank you for voting!
dead pump
1 of 4 people
found this instruction helpful.
-
Andre. M from Glendale, CA
- Really Easy
- 15 - 30 mins
-
Socket set
I first opoen the front panel of the washer. That was a bit tricky. Had to slide a thin blade between the top of the washer and the front panel, pushed in to release the "clamp" and gently raise the top, it hinges on the back.
The rest was undoing three bolts, refit the new pump and put the belt back on.
The part cost me less ... Read more then $65.00.
The repair estimate by the local repair man was $ 250.00.
I am very happy.
Thank you PartSelect.
Andre M. Roberty
The rest was undoing three bolts, refit the new pump and put the belt back on.
The part cost me less ... Read more then $65.00.
The repair estimate by the local repair man was $ 250.00.
I am very happy.
Thank you PartSelect.
Andre M. Roberty
Read less
Was this helpful?
Thank you for voting!