CW18T2A Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud grinding noise when I ran the washing machine
1 person
found this instruction helpful.
-
Eman from Wood Dale, IL
- Easy
- 30 - 60 mins
-
Pliers, Socket set
It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was s
... Read more
tiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00
Read less
Was this helpful?
Thank you for voting!
Water leak
2 of 4 people
found this instruction helpful.
-
Joe from Clearfield, PA
- Really Easy
- 15 - 30 mins
-
Socket set
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
Was this helpful?
Thank you for voting!
Washer making noise during cycles
1 person
found this instruction helpful.
-
Nat from Baton Rouge, LA
- Really Easy
- 30 - 60 mins
-
Nutdriver
I moved the washer out from the wall. unplugged washer, turned off water. Took off rear plate exposing pump. Disconnected hoses, using dry/wet vac to catch water. Took out three screws holding pump to base of washer and removed pump, belt slipped right off. Set new pump in place and put in screws. Connected hoses, put rear plate back on.
... Read more
Tilted washer back and installed belt on pulleys and motor. Turned on water, plugged in washer, started to wash clothes. Washer works fine and QUIET. I have yet to find the model number on my Maytag washer. I ordered the pump by sight (good pics).
Read less
Was this helpful?
Thank you for voting!
pulley was scraping bottom of pump
1 person
found this instruction helpful.
-
Brian from Granbury, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
First , I unlocked top cover and propped; removed front cover. tilted machine back propping front. pump is at lower right corner, removed both hoses, removed belt and three screws. reversed order completing job. You will have some water leakage removing hoses.
Was this helpful?
Thank you for voting!
crack in tub hose causing washer water to spill on to floor
1 person
found this instruction helpful.
-
Bette from S BARRINGTON, IL
- Easy
- 30 - 60 mins
-
Pliers, Socket set
raised the top of the washer to get at the front panel screws. Removed the front panel. Removed the cracked hose and installed the new one. Reinstalled the front and top panels.
Was this helpful?
Thank you for voting!
Water leak
1 person
found this instruction helpful.
-
Stephen M. from LEWES, DE
- Really Easy
- 30 - 60 mins
-
Socket set
Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks.
Re installed rear access cover and front panel.
Re installed rear access cover and front panel.
Was this helpful?
Thank you for voting!
Noise
1 person
found this instruction helpful.
-
Marylou from Old Forge, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Wrench (Adjustable)
I changed the piece easily
Was this helpful?
Thank you for voting!
Wouldn't spin after rince
1 person
found this instruction helpful.
-
joe from LAWRENCEVILLE, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Followed the great instructions on your video
Was this helpful?
Thank you for voting!
Spin cycle out of Balance - Machine walks from wall
1 person
found this instruction helpful.
-
Needham from Leesville, SC
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pu
... Read more
mp hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.
Read less
Was this helpful?
Thank you for voting!
Washer made horrible noise when entering the spin cycle.
1 person
found this instruction helpful.
-
Lance D. from Broken Arrow, OK
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Socket set
I removed the cover on the back of the machine, detatched the 2 hoses and removed the 3 screws holding in the Vertical Style Pump - with pulley. These screws are 10 mm nut-driver. The cover if I remember correctly was a standard rather than metric so make sure you have both available.
Screwed new part in, re-attached hoses an ... Read more d replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.
Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.
Screwed new part in, re-attached hoses an ... Read more d replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.
Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.
Read less
Was this helpful?
Thank you for voting!
pump bering failure
1 person
found this instruction helpful.
-
Robert from Englewood, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it
... Read more
a test then let the wife do a load of wash it worked like new
Read less
Was this helpful?
Thank you for voting!
water leaking from under front of washer
1 person
found this instruction helpful.
-
Mark from Isom, KY
- Really Easy
- Less than 15 mins
after doing some research I found out that a loose or slipping water pump belt could cause the water pump to not pump out the water correctly. Under the washer is the belt. All you do is have someone lift the front of the washer up enough that you can reach under and remove the belt. Then replace the belt back like you took it off.
Was this helpful?
Thank you for voting!
would not engage spin cycle, belt was shredding.
1 person
found this instruction helpful.
-
john from mashpee, MA
- Really Easy
- Less than 15 mins
pulled the machine out, tilted it backward to expose the bottom. pulled off the old belt. got the new belt started on the three pulleys. pulled the belt to spin it , and...............done !!
Was this helpful?
Thank you for voting!
Had a squeaky belt
1 person
found this instruction helpful.
-
Michael from Mokena, IL
- Really Easy
- Less than 15 mins
Piece of cake. Raise up the front of the machine. the belt slips of easy by turning the main drive wheel. put the belt on the two small one and then rotate the big wheel as you slip the belt into the grove. good idea to first clean the wheels of any old belt material that may be worn off. Piece of cake!
Was this helpful?
Thank you for voting!
Broken belt needed to be replaced.
1 person
found this instruction helpful.
-
Niels from Hopewell Junction, NY
- Easy
- Less than 15 mins
-
Socket set, Wrench (Adjustable)
Replacing a belt on a washing machine is a pretty easy process, depending slightly on how easy it is to access the belt. On our Maytag, the belt can be accessed directly underneith the washing machine. So, I lifted the front of the machine and put a few blocks of scrap wood under the legs to hold up the front of the machine. Once that
... Read more
was done, there was nothing else that needed to be removed to access the pullies that the belt had to go around. The motor itself is generally adjustable to allow the belt to be changed. So, I first wrapped the belt around the largest one that spins the washin machine tub, and then wrapped it around the one that spins the water pump. Finally, I loosened the bolt on the motor to allow it to move, wrapped the belt around the motor, pulled the motor back to tighten up the belt, and tightened the bolt that holds the motor in place. It's a pretty straight forward repair that narly anyone could do thmselves.
Read less
Was this helpful?
Thank you for voting!