CW18P2H Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
would not engage spin cycle, belt was shredding.
1 person
found this instruction helpful.
-
john from mashpee, MA
- Really Easy
- Less than 15 mins
pulled the machine out, tilted it backward to expose the bottom. pulled off the old belt. got the new belt started on the three pulleys. pulled the belt to spin it , and...............done !!
Was this helpful?
Thank you for voting!
Had a squeaky belt
1 person
found this instruction helpful.
-
Michael from Mokena, IL
- Really Easy
- Less than 15 mins
Piece of cake. Raise up the front of the machine. the belt slips of easy by turning the main drive wheel. put the belt on the two small one and then rotate the big wheel as you slip the belt into the grove. good idea to first clean the wheels of any old belt material that may be worn off. Piece of cake!
Was this helpful?
Thank you for voting!
Wore out Pulley/Bearing
1 person
found this instruction helpful.
-
Mark from Akron, CO
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Disconnect all water supply and unplug washer. Remove 3 screws on back panel of the washer. This will expose the pump unit. Detach belt on the bottom of the washer. Then detach two hoses that connects to the pump unit. Use pliers if necessary to disconnect hoses. Use 5/16 socket with extension to take out three bolts the connect pump to t
... Read more
he washer. That's it, now replace old pump unit and with new. Place bolts back in the 3 holes, reattached hoses, cover the back with 3 scres. Connect the belt to the pulley system on the bottom. Connect water supply and plug it in.
Read less
Was this helpful?
Thank you for voting!
Machine was wailing like a stuck pig!
1 person
found this instruction helpful.
-
Jeff from Sugar Land, TX
- Really Easy
- Less than 15 mins
Pulled that sucker out from the wall and leaned him back just enough to prop a case a beer under it. Slid up under there with the biggest dust bunny I ever seen. Yanked that old belt off and threw it away. Tried to uncoil the new one and it slapped me in the nose! Got it uncoiled and around the two smaller pulleys pulling the adjustable o
... Read more
ne in to it's limit and walked the belt around the big drum pulley. By the time my wife put down her coffee and came to see if she can lend me a hand I was done!.
Read less
Was this helpful?
Thank you for voting!
squeel
1 person
found this instruction helpful.
-
william from cypress, TX
- Really Easy
- Less than 15 mins
Tilted machine back, put a paint can under it and did R & R with belts.
Was this helpful?
Thank you for voting!
old belt broke and fell off
2 of 4 people
found this instruction helpful.
-
Tim from New London, OH
- Really Easy
- Less than 15 mins
tipped the washer back, laid on the floor, and wrapped new belt around 3 pulleys. everything works as before.
Was this helpful?
Thank you for voting!
Had the screeching noise for a few days and kept using it until it finally didn't do anything. From youtube i was able to diagnose using other peoples experiences and discovered the part i need by looking at the pictures from the model #.
1 person
found this instruction helpful.
-
Rita from Rodarte, NM
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I had my 12 year old son climb to the back and he took off all the screws necessary in the back and took the part completely off. We ordered the part and waited for it to come in. We replaced the part, the screws and honestly, the only thing we had trouble with was replacing the small cover where the hoses stick out of the washer. Was
... Read more
an easy efficient experience that may have saved me $300.00+ dollars. Thanks to my 12 year old son we got her fixed up. The washer works like brand new.
Read less
Was this helpful?
Thank you for voting!
Hinge Broken
1 person
found this instruction helpful.
-
Angela from FACTORYVILLE, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed screw, replaced hinge.
Was this helpful?
Thank you for voting!
Activator device broken off
1 person
found this instruction helpful.
-
Sonya from VAIL, AZ
- Very Easy
- Less than 15 mins
-
Screw drivers
Easy repair - with the use of a phillips screwdriver, simply remove the old device and replace with the new
Was this helpful?
Thank you for voting!
lid hinge pin broke
1 person
found this instruction helpful.
-
Charles from TEMPE, AZ
- Very Easy
- 15 - 30 mins
-
Screw drivers
I followed your video instructions. Very good video.
Other Parts Used:
Was this helpful?
Thank you for voting!
The top load cover would come off in your hand and it was so loose that the lid cover salety switch would not work
1 person
found this instruction helpful.
-
David from WINDHAM, NH
- Easy
- 15 - 30 mins
-
Screw drivers
First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both si
... Read more
des. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking
Read less
Was this helpful?
Thank you for voting!
it was spinning slowly or not at all
1 person
found this instruction helpful.
-
Louis from FREMONT, NE
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks
Was this helpful?
Thank you for voting!
Broken lid hinge pins
1 person
found this instruction helpful.
-
William from LEXINGTON, KY
- Really Easy
- Less than 15 mins
-
Screw drivers
I raised the top of the washing machine per video instructions, removed the screws, replaced broken hinges with the new ones. It was simple as that.
Was this helpful?
Thank you for voting!
Tub to pump hose worn out and leaking
1 person
found this instruction helpful.
-
steve from WATSON, MN
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Replaced the hose. two clamps and retainers. very basic repair
Was this helpful?
Thank you for voting!
Broken Hinge Pins
1 person
found this instruction helpful.
-
Robert from LIVINGSTON, MT
- Very Easy
- Less than 15 mins
-
Screw drivers
I used the putty knife to release the spring clips on the machine lid. They are about 3" in from the side of the machine. Then I lifted the top of the washer up holding the lid in place. I then used a screw driver (torx) to remove the hinge from the bottom of the washer top. The lid should come right off. Then I the removed the broken hin
... Read more
ge pins from the back of the lid with a screwdriver and replaced with the new parts. There is a little tab that the pin fits in the lid to assure you have the pin installed correctly. Then I slid the hinge back on the pin and reversed the process reinstalling the hinges and closing the top of the machine over the spring clips and your done. Very easy repair that I completed in less than 15 minutes.
Read less
Was this helpful?
Thank you for voting!