CTX22DKJR Hotpoint Refrigerator - Instructions

UNPLUG UNIT. Open freezer compartment, top door. You may want to let it warm up a bit before beginning work. Next remove single screw from small square plastic grate at top left back of freezer compartment with phillips screw driver. Remove green ground wire connection behind removed grate with nut driver. Next remove 2 screws at top ... Read more of freezer compartment holding plastic air diffuser bracket in place and holding back panel. Remove metal back panel of freezer by pulling top towards you, then angle out of compartment. Evap. fan is now exposed. I inspected and removed fan by removing two screws with nutdriver on bracket behind fan blade. I inserted nutdriver (with long socket driver)between fan blades to screws on bracket behind blade - 1 each side. After these two screws are removed, pull fan and bracket assembly out from plenum. Remove wiring from motor and remove motor to workbench. Remove round metal clamp from fan hub with needle nose pliers and slide off fan blade from motor. Also remove bracket and rubber bushing. Disgard old motor. Inspect and clean blade. Replace if necessary. Reattach rubber bushing, bracket THEN fan blade to new motor. New fan has atleast one terminal in new location and I had to use one wire extension that came with kit. Route wire behind motor and plug in new wires to back of motor. Insert fan and bracket to plenum, hold in place with one hand while reattaching screws with nutdriver between fan blades. Once fan is in place and nuts secure, I tested operation by plugging unit back in to make sure new motor ran and fan spun freely. Reattach back panel, top diffuser bracket and small grate with 3 screws. Shut door, set temp. and wait 24 hours before loading freezer. Unit good as new!

Slide pan off plastic slides. Remove glass top. Detach slides from refrigerator hooks.

Remove broken plastic slide off support beams.

You should order screws with this order.

Screws have a star top so you need a star screw driver.

Very easy to repair if you have a drill star screwdriver ... Read more bit.

Change out water valve.. to find out my temp setting was to high. My kids changed the setting.. so my ice maker didnt work. The water valve will not open until it senses the right temp. Hope this help someone. But my part was here the next day

disconnect the power to the unit. remove the retainer sctrews on the mounting bracket. remove fan motor from unit. using the rerquired tools remove the fan from the old motor and install on the new one. torque the nut until all slack is out then 1/4 turn. reinstall motor assy. and reconnect power. test the system .

removed old parts and installed new. went smooth

First I turned off the water supply. Then I removed the ice bin and the ice maker by removing 4 screws and 3 electrical connections. This allowed access to the evaporator fan which was not moving. To remove the evap fan I removed two screws that hold the fan bracket. The fan assembly now had to be pushed back and rotated to remove fro ... Read more m hole. There are 3 electrical connections that have to be disconnected from the fan, one ground wire that also is connected to the fan bracket and 2 power connections. Installing the new fan was the reverse of the above except the power connections were in a different location and i had to use the extension wires provided with the new fan to have the length needed to make the connection.

Refrigerator is not cooling. Light and fan working. Changed the capacitor.. Still not cooling. Back to discovery mode.It may be the timer
Certainly not PartSelect's fault. They have great service.

Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.

turned off water supply, took screws out of bracket, then unhooked water lines. Installed water lines onto new valve, plugged it in then screwed bracket back onto fridge, turned on water and was back operating

I had to figure out how to remove the old gasket and install the new one on my own since there were NO INSTRUCTIONS. The old gasket had to be cut off; the new one had to be warmed in hot water to make it flexible enough to flatten out. Once that was done, I had to trim excess plastic from the inside corners before the gasket would press i ... Read more nto place at the corners.

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

This was much easier than I anticipated.
The most time doing the repair was waiting for the water to soften the new seal.
The old one pulled right out, she cleaned it off and I pushed the other into place.
Part select got it to me quicker than expected and when I phoned the order in and inquired about whether I neede ... Read more d the retainer behind it she asked someone and found I did not which saved me $16.
They are great and this whole transaction went too smooth...

Repair was very simple. Removed refridgerator bottom back panel, about 6 or 7 screws. disconnected bad valve, installed new valve , connected water supply line and then reinstalled panel. Took about 15 minutes from start to finish.

Found the part I needed in only a few minutes on the website and ordered it in less than 5 minutes. The part came within 2 days and I simply removed 2 screwes from the old part and installed the new part and replaced the 2 screws , the easiest repair job that I have ever done in my home. Thanks

Remove three screws insert part; manually checked out drive and waited for ice to buildup and it worked like new.