CSZ22DRAAD Hotpoint Refrigerator - Instructions

Was concerned that new icemaker was quite a bit different than the one we were replacing. Called GE to confirm it was correct.

Went ahead and installed the unit, using the supplied electric cable adapter.

A little difficult to deal with the extra cable, but everything worked OK and it's making ice normally.

First I propped up the door. Then I removed the 2 screws that hold the hinge on. AT this point you do need someone else because the door swings loose. I attached the new bracket and lowered the door. It went verey smooth. I ordered the new bracket after reading the installation stories from others who just repaced the plastic pieces. Its ... Read more worth the extra money to just put on a new bracket

Turned off The water supply. Removed the back panel corner(nut driver). Removed valve (nut driver) and water supply inlet line. Cut the old outlet lines at the valve (new lines are push in) disconnected electrical lines, Reinstalled inlet line and electrical lines. Reinstalled valve and back panel. Turned on the water. Ice maker fi ... Read more lled with water and a short time later I had ice. Easy job.

Found broken pieces of deflector in delivered ice. Removed dispenser, carefully disassembled it, marking fasteners, sprimgs, and levers. Local repaimen say no replacement part available, must replace entire ice maker @ $350. Found exact part in your online reference, ordered at price of $3.76, part arrived two days later--perfect fit, exa ... Read more ctly same as original. Reassembled, and it works exactly like new. Family very happy. Good job!!!!!

I pulled the refrigerator away from the wall and turned off the water to the refrigerator and unplugged it from the wall. After removing the icebucket from the freezer I located the mounting screws, loosened them, unplugged the electrical connection below the icemaker and carefully removed it from the freezer. I unpacked the replacement i ... Read more cemaker, matched it against the original and attached the electrical connection adapter. Using the slots provided on the new icemaker I placed it over the mounting screws after aligning the water inlet pipe properly. I tightened the mounting screws while maintaining the icemaker in a level position. I plugged in the electrical connector. Then I replaced the icebucket, plugged in the refigerator back into the 110VAC outlet, turned on the water and repositioned the refrigerator in it's normal position.

Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.

I'll be back...

two screws and a connector were removed to replace the timer.
Timer was located on the top front of fridge

I followed the directions of Steve on the installation video. He makes it easy to do the repair with his step by step description of the installation. I have repaired three different aging appliances with help of Steve and PartSelect's very helpful Customer Service.
I wish Steve a wonderful retirement and hope PartSelect can find ... Read more someone as easy to follow for future videos. The videos are priceless for the repairs.

Kenmore 24 cu.ft. Side by Side Refrigerator. The bottom cam on the fresh food side of our refrigerator broke causing the door to stay open about 4 inches. We had to lift the door up about an inch to close it. We removed the top bracket cover by removing one screw with a screwdriver. We then removed two screws with a ratchet and socket ... Read more , to remove the top bracket, which allowed us to lift the door up and off of the refrigerator. We removed two screws with a socket to remove the Door Cam and Shim. We replace the Shim, and Door Cam with the two screws. Make sure you line the Cam up with the hole it goes over, and tighten it up. Place the door over the bottom bracket, and replace and adjust the top bracket and cover.

Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugge ... Read more d it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.

The internal water line was leaking. I could not find any repair parts for my refrigerator but the GE 5/16 water line was the same size. I purchased 6' of tubing and two unions. Make sure the clean and square. If possible, make the cuts in a spot where you can use the pliers and wrench to tighten the union. I cut approximately 2' out of t ... Read more he existing line and replaced it with the same length of new line using the 2 unions, one on each end. Took about 5 minutes.

Installed the new timer.