Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
door would not close by itself - broke cam riser
My right door (food door on side-by-side) stopped closing - I found pieces of the plastic washer (cam riser) on the floor. After reading the stories on the web I decided to order the new part - and YES there are many universal parts that work for Kenmore/GE. The part comes with two parts (hinge and cam riser) - you should install both to insure a good fit. I took 3 blocks of wood and a shim and supported the bottom center of the door, unscrewed the hinge off and dropped it out (3 minutes). The "only" tough part was unscrewing the cam riser from the bottom of the door - it required a very small socket and you will only have about 6-8 inches of work space. Be sure you have a socket that fits before you take the hinge off. The entire repair took less than 30 minutes and contrary to some of the posts, you DO NOT need to take the door off. Good as new again!
Our Cats tail got stuck in the door and caused the door hinge to move enough to crack the nylon cam and we were wondering why the cat sat next to the refrigerator all after noon one day and let my 4 year old pet him (maul) when that never happens
Removed cats tail and proceeded to look for parts on line. received parts. stacked a set of books under raised door after unloading items from door to reduce wieght unbolted both sides of hinge. Reassembled both hinges. pulled books out and done in 15 minutes. Works better than new!! The cat no longer goes near the open doors. Fixed 2 problems!!
Remove glass shelf, then remove drawer. Remove 2 screws holding old broken rail in place and replace using the same screws. Replace the drawer and glass shelf.
Removed door off hinge , remove bottom hinge, drill out rivet, lift off old cam & replace with new cam ,add new 1/4' BOLT(NOT SUPPLIED) to location where rivet was, reinstall bottom hinge & door ,check alignment, works perfect.
Placed blocks under the refrigerator door to take weight off the lower hinge pin. Removed the hinge by removing two screws into the refrigerator and two screws into the bottom of the door itself. This allows the hinge to be removed so the old nylon "closer" pieces can be removed (the one attached to the refrigerator has a rivet holding it in place so that has to be drilled out and replaced with a 3/16 inch bolt and nut). After re-attaching the nylon "closer" to the refrigerator side of the hinge and placing all the shims back in place, I re-attached the hinge to the door first, then the half hinge to the refrigerator. Had to line up the holes, tighten the screws and presto, the door closes like it was new again.
The freezer door side is more difficult as there are wires and a water line to work around.
After fixing my washer this was a snap. After lifting out drawer and shelf only two screws needed removal. I think it was easier putting it back together! It is sites like these that make it possible for men to feel like men!
I blocked the door up with one 2X4 Then removed the lower hinge, installed the closing cam. Then I found that I needed one more closing cam that I didn't order the first time. This other one mounts to the lower section of the door and both cams set together. Re-ordered another cam. When it came in I installed it. Between ordering both parts I had them both in three days. The best to Parts Select I now know where to buy my parts if needed again.
I removed the screws holding the remaining portion of the slide rail in place. I was able to install the new rail by simply attaching the part to the fridge using the same screws. Having an electric screwdriver made the job very easy.
I removed the top hinge by removing three screws, I then lifted the door off the bottem hinge and set it aside. I then removed the two screws holding the bottom hinge,removed it and installed the new part. I removed the broken part from the door by removing one screw-installed the new part and set the door in place and reinstalled the top hinge. The door is now properly aligned and working like new. I spent as much time writing this as I did on the repair
First I placed a 2x4 under the frig door to keep it in place while I removed the hinge on the bottom of the door. I removed two screws holding the hinge and one screw holding the washer in place. I also loosened a screw adjacent to the washer so that I could more easily remove and replace the washer. The parts went in easily. The repair took much less time than I anticipated.
After reading the stories here, I purchased one door closing cam. After getting into the problem area, I realized I needed 2 cam, so I put the door back together and ordered another cam. If you have this problem, buy 2 cams.
First, I was glad I read other posts on this repair as I would have only purchased one of the replacement cams when I needed two! I removed the top door hinge with a screw driver (cover) and small socket set for the door hinge. I then removed the door and removed the bottom hinge (socket set). The bottom hinge had a small rivit that held the bottom cam in place. I used a hack saw to cut off the rivit and replace the cam and secured it with a small machine bolt and nut. I then laid the door on its side and removed the top am from a bracket attached to the bottom of the door. I relaced the cam (second one) and reinserted the screws. I reattached the bottom hinge and then placed the door on the bottom hinge pin. I then held the door in place while inserting the top hinge pin bracket into place and retightening the top screws. I replace the cover with a screw drive which was the ahrdest part in trying to find the hole the small screw gets inserted into. DONE!
The fresh food side of my refrigerator had started to drop because of a broken cam riser.
First I pulled the door up to the top hinge and propped it up with phone books. Secondly I used a nutdriver with an 8mm attachment and removed the bottom hinge. Thirdly, I removed one screw from the bottom of the door with a socket and 8mm attachment and removed the broken cam riser. Being careful as to take note of how the cam was positioned. I then attached the new cam riser to the bottom of the door, attached the bottom hinge to the refrigerator, making sure the pieces (cam riser and plastic on bottom hinge) matched up and after everything was tight, removed the phone books. Remember to first remove the vent on the bottom of the refrigerator and it is much easier to maneuver the door if you empty the contents on the inside. Very easy, I am not very mechanically inclined and this is the first job that I finished in the amount of time as stated. Also, do not chance just the riser as both pieces will be worn. Hinge assembly comes with all you will need.