CSX22GKC Hotpoint Refrigerator - Instructions

Followed Partselect video on how to replace cam riser. Very, very helpful!

Best for 2 people on this repair as 1 person needs to hold the door and the other position the bottom pin in place on reassembly. On my side by side I was replacing the cam on the cold food side, not the freezer. But I got down and inspected both the broken cam and the cam on the side that wasn't broken to understand how the parts fit tog ... Read more ether. Each door has 2 cams that work/fit together. So be sure the one you are replacing is installed properly (flat side towards the door body). Remove all contents from inside door including the shelves. Use a phillips screwdriver to remove the cover plate on the top hinge. Use tape or a marker to mark on the refrigerator top a corner of where the bracket is positioned, for proper placement on reassembly. While someone is holding the door, remove the 2 bolts from the top bracket (or the back one is just loosened so bracket can be moved out of the way). Lift door off the bottom pin. Turn the door on its side to expose the bottom bracket. There should be 2 bolts here. The furthest one from the pin only needs to be loosened. The other bolt will need to be removed but as you do this be sure to not let the other 2 metal pieces fall out. Remove the broken cam and replace with the new part. Realign the parts and bracket over the pin rod hole and tighten both bolts. Replace the door onto the bottom pin. Then add top bracket and align it to the marking and screw back in these 2 bolts. Test door for any needed adjustments (I had none). Then replace the top bracket cover with its screw. Voila! Clean the shelves and put them in the door and fill them up. :-)

I followed your terrific video. I first got all tools ready, covered a table in cardboard, and removed food from the fridge door. I removed the cap and screws on top of the door hinge. Lifting the door off was simple, and after laying the door on the table, the retaining screw was easily loosened, and the cam screw removed. The only probl ... Read more em was that half the thin gasket under the broken cam was missing. No new gasket came with the part. I wanted the new cam to lay flat, so I made a partial gasket from a matchbook cover and filled the gap. It all went back together quickly. Just have tools ready beforehand. Ten minute job, unless you have to make a new gasket or part of one. Thanks, guys.

Using the #2 Phillips screwdriver I removed the top hinge cover from the top of the freezer door. Next I used the 5/16 nut driver to remove the 2 bolts holding the top hinge in place. Once it was removed I was able to lift the door off the bottom hinge. Placing the door on a flat work surface I loosened the bottom bolt holding the cam in ... Read more place. I next removed the bolt holding the hinge in place. I was then able to remove the broken cam and replace it with the new one. I then replaced the bottom bolt making sure the hole for the cam and the hole for the hinge are lined up. I then tightened the bottom hinge bolts. I carefully placed the door back on the bottom hinge and put the top hinge back on.

I ordered a door closing cam (4320595) to start with and then relized I needed Bottom Hinge Assembly which I ordered#4326874. I had no problem installing. I have returned for credit the door closing cam. I HAD NO TROUBLE INSTALLING THE BOTTOM HINGE ASSEMBLY. ONLY TOOK 10 OR 15 MINUTES. I am a retired building contactor and hade ... Read more all the toos necessary.

I ordered a cam riser for the refrigerator door. I watched the "how to" video the day I ordered the part. It took about a week to get the part, but I was ready when it arrived. The 'how to' video was a big help. It showed me how to take off the door and replace the part. The process was quite simple! Oh! Don't forget to turn the ref ... Read more rigerator on again!

Just used a screw driver to remove the old part and install the new one. The gal on the phone from parts select was excellent helping me find the correct part. Highly recommend this web site.

Emptied the old draws and removed the old sliders. Took time to screw the new ones in. The draws are not as nice as the original ones.