CSX22DKC Hotpoint Refrigerator - Instructions

This my second time to do it after 8 years. Took 10 minutes.
1 Remove all the contents on the side door
2 Remove the 2 bolts on top connecting the door to the refrigarator
3 Lift and remove the door up and put it the side
4 Clean and remove the old door closing cam put the new one
5 Door ref is fixed

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Buy ( 2 ) cams !!!! removed hinge cover and hinge on top of the door, ( 2 screws )...lift door off of the bottom hinge and lay door on the floor, remove broken cam on bottom of door with nut driver, ( 2 screws ) , install new cam..... remove the bottom hinge off of the front of the refriger ... Read more ator with nut driver, (2 screws ).... saw rivit off and remove old cam, install new cam and secure with new bolt and nut,... reinstall hinge back on bottom front of refigerator.....replace door back onto the bottom hinge.....install top hinge back onto the top of the door....replace hinge cover......done !

Followed step-by-step instructions in previous post. Note that there are TWO approaches, both of which work.

Option 1) Order TWO cams (PS297995), drill out the rivet holding the frame's cam, and replace it with a nut and bolt. (See post on 07/19/09.)

Option 2) Order the entire hinge assembly (PS290199), which i ... Read more ncludes the door's cam and an assembled frame hinge and cam. (See post on 10/29/08.)

We opted for Option 1 which was pretty easy. Option 2 would be even easier and take less time but costs about $9 more.

Thanks to previous posters for excellent instructions!

Pay close attention to how you disassemble everything. You might even want to take a picture. I taped all the screws right where I unscrewed them, to make sure they were replaced in the right section. Also use the picture diagram that on the computer.

We taped the door with 3 pieces of duct tape, then put boards under it. Used socket set to remove cam and then cut off rivet so we could just use a screw to keep in place. . . Just for your information, I ordered 2 cams, and was glad I did as I need 2 to make the repair. . . Didn't read about this online or on order recommendation. ... Read more The cams go 1 up and 1 down thanks for the installation repair stories, it inspired us to "do it ourselves " and we saved about $75 to $100. 00

This was an extremely easy repair. The old light shield snapped out and the new one snapped in.

The disassembly and reassembly was straightforward but the parts diagram was very helpful to help you get it back together. Make sure you get the convexity of the clip that retains the clear plastic barrel to the auger pointing in the right direction. The metal plate that that comes out with the assembly seems to rust as fast as the au ... Read more ger, so you should just order that when you order the auger. I did not replace the plate so I cleaned it and painted it with epoxy paint before I reassembled.

Emptied the old draws and removed the old sliders. Took time to screw the new ones in. The draws are not as nice as the original ones.

watched the video on changing the cam and then did the repair as per the instructions. the job was easy and now the door works as it should. that saved me lots of money by doing it myself. thanks, Martin.

there was rust inbedded in the ice cube. replaced the front plate in the ice maker bin. If you can't remember what parts you remover, take pictures of the replacement

I followed your terrific video. I first got all tools ready, covered a table in cardboard, and removed food from the fridge door. I removed the cap and screws on top of the door hinge. Lifting the door off was simple, and after laying the door on the table, the retaining screw was easily loosened, and the cam screw removed. The only probl ... Read more em was that half the thin gasket under the broken cam was missing. No new gasket came with the part. I wanted the new cam to lay flat, so I made a partial gasket from a matchbook cover and filled the gap. It all went back together quickly. Just have tools ready beforehand. Ten minute job, unless you have to make a new gasket or part of one. Thanks, guys.

Using the #2 Phillips screwdriver I removed the top hinge cover from the top of the freezer door. Next I used the 5/16 nut driver to remove the 2 bolts holding the top hinge in place. Once it was removed I was able to lift the door off the bottom hinge. Placing the door on a flat work surface I loosened the bottom bolt holding the cam in ... Read more place. I next removed the bolt holding the hinge in place. I was then able to remove the broken cam and replace it with the new one. I then replaced the bottom bolt making sure the hole for the cam and the hole for the hinge are lined up. I then tightened the bottom hinge bolts. I carefully placed the door back on the bottom hinge and put the top hinge back on.

The replacement part came with a one page instruction sheet. Following those instructions I cut the two hoses on the old resivour and removed it. I then cut the hoses on the new resivour to desired length (all inside the refrigerator). Using the two couplers provided with the new resivour I hocked the two hoses together and tightened th ... Read more em with a wrench. It took longer to clean the refrigerator than it did to replace the part. Instruction sheet was very helpful

Just used a screw driver to remove the old part and install the new one. The gal on the phone from parts select was excellent helping me find the correct part. Highly recommend this web site.