My Orders
- Home
- CSX19LABBWH
- Instructions
CSX19LABBWH Hotpoint Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The light inside the oven had burned out
3 of 7 people
found this instruction helpful.
-
Catherine from SEATTLE, WA
- Very Easy
- Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
plastic cam risers on fresh food door worn out
1 person
found this instruction helpful.
-
Fred from Port St Lucie, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I unloaded the door and took the cover off at the top of the upper hinge (1 phillips screw) I then unbolted the upper hinge (2-28mm bolts) and lifted the door off. I was surprised how light it was. I laid the door down and installed the new cam riser on the door. I then unbolted the lower hinge (2-28mm bolts)and installed the new hinge.
... Read more
r />I lubed the 2 hinges with vaseline and put the door back on the lower hinge. I then reinstalled the upper hinge and cover. It took about 15 minutes, and a lot of that was cleaning up. Oh yes, to get at the lower hinge you have to pull off the lower grate that covers the coils. It just snaps off and on. It was a very easy job.
Read less
Was this helpful?
Thank you for voting!
The plastic hinge stops broke.
2 of 4 people
found this instruction helpful.
-
james from olney, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I cleaned out the door and removed the top hinge. Lifted the door and layed it on the floor. Removed bottom hinge from refridgerator installed new hinge. Replaced plastic stop on door. Used broke hinge to align it and tighten. Lifted door onto new hinge and installed top hinge. Instead of buying $35 dollar hinge buy 2 plastic stops. You
... Read more
'll have to drill out a rivet on bottom hinge but it will save over $30.00.
Read less
Was this helpful?
Thank you for voting!
Door wouldn't shut and 1 broken drawer slide
1 person
found this instruction helpful.
-
Matthew from Brighton, MI
- Really Easy
- 15 - 30 mins
I removed the drawer and glass shelf, removed 2 screws and replaced with new drawer slide in reverse order. I removed the contents of the door, the top hinge, and then laid the door down. On the bottom of the door, I replaced the pivot piece (provided) and then I replaced the hinge on the lower right side of the refrigerator box (2 scre
... Read more
ws with a nut driver bit). I now reversed the order to re-assemble the door and finally re-aligned the top hinge to adjust the door fit. Less than 30 minutes total. EASY!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The food compartment door would not close completely.The botom door cams were worn.
1 person
found this instruction helpful.
-
Joseph from Pittsburgh, PA
- Easy
- 15 - 30 mins
-
Socket set
I removed the door from the bottom hinge assembly by removing the top hinge assembly.
1. Installed the cam to the bottom of the door.
2. Installed hinge and bottom pin & cam to the refrigerator.
3. Reinstalled door and adjusted front roller height to make door close better.
1. Installed the cam to the bottom of the door.
2. Installed hinge and bottom pin & cam to the refrigerator.
3. Reinstalled door and adjusted front roller height to make door close better.
Was this helpful?
Thank you for voting!
Emptied refrigerator door shelves. Supported door with 4x4 blocks.removed old door hinge and replaced with new.
1 person
found this instruction helpful.
-
John from Medford, OR
- Easy
- 15 - 30 mins
-
Socket set
Emptied refrigerator door shelves. Supported door with 4x4 blocks. Removed old door hinge and replaced with new door hinge and cams. Pleased with end result and dealing with PartSelect.
Was this helpful?
Thank you for voting!
Fridge wasn't cooling and half freezing
1 person
found this instruction helpful.
-
Wendell Hayes from Dillob, SC
- Really Easy
- 30 - 60 mins
-
Screw drivers
Part was perfect fit .Removed fan .three screws.replaced that s it
Was this helpful?
Thank you for voting!
Door wouldn't close
1 person
found this instruction helpful.
-
James from Dayton, MD
- A Bit Difficult
- 1- 2 hours
-
Socket set
It seems my refrigerator was old enough [1987] that the spacing on the holes for the bracket were different than the part that is currently sold. The holes on the new bracket were 30 mm apart on center, but on the old bracket they were 20 mm apart on center.
Clamped the old and new brackets together in a vise to use the old br ... Read more acket for spacing and drilled a new hole through the 4mm of steel.
After which it was a snap installing the new hinge assembly.
Clamped the old and new brackets together in a vise to use the old br ... Read more acket for spacing and drilled a new hole through the 4mm of steel.
After which it was a snap installing the new hinge assembly.
Read less
Was this helpful?
Thank you for voting!
door would not close by itself - broke cam riser
1 person
found this instruction helpful.
-
Mike from Alpharetta, GA
- Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
My right door (food door on side-by-side) stopped closing - I found pieces of the plastic washer (cam riser) on the floor. After reading the stories on the web I decided to order the new part - and YES there are many universal parts that work for Kenmore/GE. The part comes with two parts (hinge and cam riser) - you should install both to
... Read more
insure a good fit. I took 3 blocks of wood and a shim and supported the bottom center of the door, unscrewed the hinge off and dropped it out (3 minutes). The "only" tough part was unscrewing the cam riser from the bottom of the door - it required a very small socket and you will only have about 6-8 inches of work space. Be sure you have a socket that fits before you take the hinge off. The entire repair took less than 30 minutes and contrary to some of the posts, you DO NOT need to take the door off. Good as new again!
Read less
Was this helpful?
Thank you for voting!
Old hinge washer worn out.
1 person
found this instruction helpful.
-
James from Lockport, IL
- A Bit Difficult
- 15 - 30 mins
-
Socket set
First I placed a 2x4 under the frig door to keep it in place while I removed the hinge on the bottom of the door. I removed two screws holding the hinge and one screw holding the washer in place. I also loosened a screw adjacent to the washer so that I could more easily remove and replace the washer. The parts went in easily. The repa
... Read more
ir took much less time than I anticipated.
Read less
Was this helpful?
Thank you for voting!
Had a 'ticking' sound
1 person
found this instruction helpful.
-
John from PARKVILLE, MO
- Easy
- 30 - 60 mins
-
Socket set
Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side o
... Read more
f the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.
Read less
Was this helpful?
Thank you for voting!
Noisy
1 person
found this instruction helpful.
-
Brad from SPRING MILLS, PA
- Very Difficult
- More than 2 hours
I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people
found this instruction helpful.
-
Louis from LEAGUE CITY, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
Easy
Was this helpful?
Thank you for voting!
plastic cam on hinge cracked
1 of 2 people
found this instruction helpful.
-
George from Grayson, GA
- Really Easy
- 15 - 30 mins
-
Wrench set
Supported the door on the bottom them removed the 3 screws holding hinge to door. Installed new hinge assembly. Had a litle trouble installng screw in bottom of door due to alignment issues with cam & metal piece. It finally went in when I loosened 2nd screw in bottom of door.
Was this helpful?
Thank you for voting!
The door hinge assembly at the bottom of the door was broken.
1 of 2 people
found this instruction helpful.
-
james from dothan, AL
- Really Easy
- 15 - 30 mins
-
Socket set
removed the door hinge assembly & replaced it with the new assembly.
Was this helpful?
Thank you for voting!