CSP2770EW0 Whirlpool Dryer - Instructions

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I ... Read more get my refund of the $107.26 for the parts that I never received!!

Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!

Removed the screws replaced the belt and lubricated the wheels and that fixed my Knocking and it runs like when I first got it

Ezee pezee lemon squeezee.

Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pul ... Read more ley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.

I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace t ... Read more hem all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.

Very easy do it yourself repair, and saved at least $300.00. I watched a video and it took me less than 20 minutes to complete repair. Part fit perfect and I have already ordered another to keep as a spare.

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to ... Read more be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

Take pictures along the way.
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of ... Read more the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too ... Read more shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, rol ... Read more ler, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place locate ... Read more d just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.

Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.

I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. R ... Read more einstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.