CSK27PFXABB Hotpoint Refrigerator - Instructions

Unplugged fridge.Removed 2 screws holding a panel. After panel removed took off old fan and inserted new. Quite simple.

removed drawer, unscrewed old slide, screwed on new slide, voila! finished! I was very pleased with PartSelect -- ordering was easy, the correct part came quickly, and packaged very well. All of life should work so smoothly!

I removed food from shelf over crisper drawer, then removed shelf and crisper drawer, removed two phillips head screws in right side rail and replaced rail.

Easy as 1-2-3

First take all your junk off the shelf (with the broken rail of course), take the glass shelf off. Remove screws (phillips). Throw away old rail. Replace new rail, tighten screws. Replace shelf, replace junk. You're done.

1) The large drawer is first removed from the guide that remained on the side wall.

2) Removal of the light shield from the rear of the glass shelf to facilitate glass shelf removal by lifting the rear edge of the glass and remove it.

3) Unscrew two phillips head screws holding the remaining pieces of the plastic guide to the interior side panel of the fridge.

4) Examine the replacement guide and insure that the nylon guide and stop parts are clicked into place. If unsure, look at the guide on the other side to ensure that both are present and completely seated before installation of the replacement guide. (These usually fall out of the guide during shipping and should be in the bag with the guide!)

5) Once the guide is outfitted with the nylon guides, secure the new guide with the two phillips screws and DO NOT over tighten, remember you are dealing with plastic guide and steel screws going into a steel cabinet.

6) Re-install the glass shelf, followed by the light shield and finally the large drawer which should slide out smoothly to the stop and back closed without any drag.

7) A successful installation usually includes giving the drawer and glass shelf a good cleaning that probably could be done to the entire fridge side of the unit.

I would recommend removing the dor first as I had to do this after fighting with the drawer to get it out.
There is a cap on the hinge that has one screw, then two nuts and the door is off. From there the drawer rails are easily replaced.

The drawer slide broke and I just removed the 2 screws that were still in the side of the refrigerator. I then screwed the new drawer slide in the same holes and it was done!! Simple, simple....even for me, the housewife.... ; )

This was so easy! I got the part number off of the broken part, ordered online, and it was delivered the next day!!! So fast! Then I just unscrewed the broken part and reused the existing screws to install the new one. It took about 5 min.

Thanks for making everything so fast and easy!

Turned water supply off; pressed dispenser sw to release presure ; cut tubing holding reservoir ; nuit driver to release screw holding reservoir and pulled out ; took outside and used hose nozzle to try to clear; did not clear at first then took weedeater string and disloged something and water flowed freely; turned out had to change waer solenoid valve (both) as the one for the water dispener was also plugged which did not show up before.
P.S. Had back flow water thru system before and changes of parts. Water flowed freely.

Took the drawer out, unscrewed 2 screws, replaced the part, put the drawer back in.

I removed the two screws from the old broken rail using a regular star screw driver and replaced the new rail you sent us. Took only 2 mints to do all.

I removed the drawer and broken piece, then I screwed in the two screws to put the new piece in place. I then had trouble putting the shelf back in place due to the piece being a little bent. I loosened the front screw and was able to manuver the shelf in place with a little force. The new bracket works great.

First I removed the two screws that held the slide in place. I then pulled the slide out and lined up new slide and reinstalled the screws.

1st I unscrewed the side rails after I removed the drawer. I saved the screws and both rails until I received the new ones.There were 2 screws in each side. 2nd I looked online at the parts select web page. The exploded diagrams were extreemly helpful. Like most people my appliance book does not have this feature. I ordered the 2 rails for the drawer on Sunday morning and the parts were here by Wednesday afternoon..very good service in my opinion. I then proceeded to replace the two side rails with the screws that I saved from dismantling them. I then put the drawer back into the refrigerator and it worked perfectly. This repair was easy and it saved me a $60.00+ dollar service call and a longer wait period to get the repair done! I will continue to use part select.com for all my appliance repair work. Thanks

Unscrew the two screws with a screwdriver and replace the new slide rail with the same screws.