CSK20GABBAD Hotpoint Refrigerator - Instructions

Not really sure of the age of this fridge, as we bought the house 2.5 yrs ago.

I'm one who if it can go wrong, it will, so not realizing how stable the door was from just having the top hinge and the magentic gasket, I declined to prop the door up on blocks the way some guys say the did, and instead removed the top hinge and li ... Read more fted the whole door off the bottom hinge. I traced the outline of all parts with a felt pen before removing them, figuring I'd need witness marks to help with realignment after the install.
Nut driver might've been an easier choice than the socket set, but the only ones I have a brittle and I've broken the 5/16"...
All parts came out/off easily. The new bottom hinge and the old top hinge (both on the fridge side) practically aligned itself right on my marks, and the new cam (door side) just needed to be held while the screws were tightened. I used the extensioni rod off the ratchet to drive the screws most of the way (making a nutdriver out of it).
Parts were exactly as advertised, although there was a note in the package that stressed the need to replace both parts at the same time due to material differences in the original and replacement parts. Since the cam is sold separately without the hinge, it would be good for the website to reflect that before the purchase is made. Also, even though it was only the cam on the hinge and not the whole hinge that needed to be replaced, I could've bought hte two cams separately and drilled out the rivet as another person had done, but for the $5 difference in cost, why bother?
Door now closes itself as designed, albeit slower than the freezer side, but the Wife says it always did that.
Also interesting that when first assembled, the door DIDN'T close itself at first... not sure it it needed to wear a litle, or if it just needed the added weight of having items back in the door shelves.
Love the great website... just typed in the model number and the parts I needed, complete with drawings to make sure, were right there. Great UI.

removed the door hinge assembly & replaced it with the new assembly.

I removed the top hinge, lifted the door off the bottom hinge, rmoved and replaced the bottom hinge assembly, and reinstalled the door. I then aligned the door and reinstalled the upper hinge. The fridge works just like new!

removed door, removed old cracked riser aand replaced with new. You have a easy to follow parts site and very good prices. I will use you for all my future repairs.

Cake walk repair.

Unload the door then close it.
Remove screw holding plastic cover over hinge on top.
Remove 2 bolts attaching the hinge on the door.
Slowly open and lift door off of bottom hinge lay on counter.
Unscrew bolt, insert new cam, tighten bolt ,set back on bottom hinge, center install top hinge, ... Read more tighten and install cover. tool me 6 minutes.

Removed 2 screws holding top hinge. Removed door. Removed 2 screws that holds the door stop and cam riser replaced cam riser, provided, replaced stop and screws. Removed 2 screws holding lower hinge replaced with hinge, provided, replaced screws. Put door in place and replaced top hinge and srews. Job done

After recieving the part overnight (Very unexpected speedy delivery!) I propped the freezer side door up with a 4x4 and 2x4 and the old part came right off and the new part went right on with no hassels, Done in less than 15 min!!!!
The new part even came with step by step easy to follow directions.

Emptied the refrigerator door so it was easier to take off. Used a screwdriver to remove the screw on the top hinge. Lifted door off bottom hinge. Laid the door down so I could take the bottom hinge off. Removed worn out parts and placed the new one on. Slipped door back on hinge,made sure it would close properly and was lined up with fre ... Read more eze door. Put top hinge back in place. Done!! Now door finally shuts on its own again!!! EASY!!!

remove plastic top hinge cover then twoscrews holding door with door closed it rested against freezer door then lefted off door put on flat surface remove tow screws at bottom of door installed new cam

Removed all items from the door shelfs.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now ... Read more level with the freezer door.

I had to remove the top hinge of the door and shut off the water supply to the automatic ice maker. I then unhooked the water line and pulled it through the guide as I took the door off. Once the door was off, I removed one bolt with the nut driver and replaced the cam. I reversed the above actions and replaced the door. It is very i ... Read more mportant to adjust the door so the seal fits tightly and evenly all round the door. It was a relatively simple procedure that went very smoothly.

Followed other messages to complete fix. Simple overall.

Please note that if you buy the hinge assembly, you get spacer parts that mate. If you don't you have to hack-saw the rivot off the old hinge assembly to do your repair. Hinge assembly cost more but less work.

The refrigerator door would now close and notice broken plastic on the floor. It is a 1990 or so GE fridge. To repair - ordered the Cam Riser (the plastic piece that broke and the matching lower door bracket.

Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the d ... Read more oor onto the upper guide then fastened the new hinge with the socket wrench.

Easy job .. around 20 minutes.

I could see a broken part but couldn't tell exactly how it was oriented on the hinge. I bought just the cam riser but then thought I needed the hinge kit based on what I read on this site. Then I saw better pictures of the hinge kit on another site & realized there are 2 cam risers that meet. The one riveted to the hinge was fine (in m ... Read more y case) - I only needed the upper one...a very inexpensive repair. Do NOT remove the door for this repair. Slide the door up a bit while closed and use a pint-sized paint can to prop it up. Make the repair and remove the can...done.

First I bought the right tool to remove the hinges.
Then replaced the hinge with the two cams.
Now the door closes itself.