CSH22GRXAAA Hotpoint Refrigerator - Instructions

Found broken pieces of deflector in delivered ice. Removed dispenser, carefully disassembled it, marking fasteners, sprimgs, and levers. Local repaimen say no replacement part available, must replace entire ice maker @ $350. Found exact part in your online reference, ordered at price of $3.76, part arrived two days later--perfect fit, exa ... Read more ctly same as original. Reassembled, and it works exactly like new. Family very happy. Good job!!!!!

Procedure for Replacing the Ice Chute Plate
1. Turn off the power.
2. Snap off the outside trim ring. Use a plastic screwdriver to avoid scratching the cabinet.
3. Locate the three small holes below the control panel facing, just above ice chute. The center hole is not used. With a small, blunt, object (wire – blunted nail) ... Read more that is slightly smaller than the holes, push up rather firmly up through the outer holes to release front control panel.
4. Remove the three wire connectors from printed circuit board. Firmly pull/pry them straight out of retaining clip. Use caution: Excessive force will break clips.
5. Release the secondary panel by removing four screws (one in each corner).
6. Remove the flap assembly.
7. Clean all accessible areas with 1/10 bleach water to sanitize. Rinse the cleaned area with clear water and thoroughly dry everything before re-assembling the panel.
8. Install the new flap assembly.
9. Re-installed everything in the reverse order and check the functionality.
10. Order a spare ice chute flapper to be ready for the next event.

- Disconnect the valve assembly and remove electrical connection to water dispenser valve to prevent accidental water discharge

- Disconnect tubing from valve assembly, remove and keep compression nut.

-Disconnect tubing from junction to door tube remove and keep compression nut

-Remove screws used to moun ... Read more t reservoir, pull tubing into main refrigerator compartment and remove old reservoir and tubing.

- Note that one of the tubes on the new reservoir is 2' too short.

- Go to hardware store to purchase 5/16" universal tubing compression junction.

- Install reservoir and feed tubing through holes in main refrigerator compartment.

- Route tubing through woven tubing protectors and clips.

- Trim tubing to length and install in valve using old compression nut.

- Splice the piece of tubing trimmed from supply side of reservoir to the outlet side tube using the fitting purchased from the hardware store.

- Connect end of tubing to existing junction using old compression nut.

- Re-connect wires to valve solonoid and test for leaks.

- Re-install valve assembly to refrigerator frame.

Took unit apart but did not take photos of how to put unit back together, so needless to say it took longer then it should have. My error. Ordering the part was very easy and within days the part arrived at my door. Should the need arise, I would order again from Part Select.com.

This was a very easy fix. I cut the water lines at the reservoir, coupled the old lines to the new lines with two plastic barbed fittings used for outdoor drip irrigation. All I had to do was pull the old lines out and the new lines followed. Easy as pie!

I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and ap ... Read more plied a little lubricant to the cam and job complete.

you must pay careful attention when taking the dispenser apart,especially the long rod that controls the deflector,but if close attention is payed to disassembly you should have no problem.

I simply removed the screws holding the plastic face plate to the old auger/ice bucket and attached it to the new one. It was a simple procedure

replaced lights in refrigirator and freezer

1. Turned off the water supply to the refrigerator.
2. Removed the front panel and disconnected the water line to the front left.
3. Removed the left rear (freezer side) panel and disconnected the reservoir from the main water supply input. This was a little tricky to figure out. You must push in the water line at the same ti ... Read more me pushing in the coupling. Then pull the line out while keeping the coupling pressed in.
4. Removed the screw that holds the reservoir to the back of the refrigerator.
5. Pulled the old reservoir out and replaced it with the new one.
6. Basically the rest is the reverse of the above. It took a little bit to fish the lines through the original path they came.

Overall this was an easy repair. If I had known how the coupling in step 3 worked this would have been a 15-minute project.

Remove contents of door , Remove top hinge cover - phillips screwdriver , remove top hinge screws ( 2 ) - socket wrench , lift door off lower hinge pin , lay door on edge , remove cam retention screw ( 1 ) - socket wrench , remove broken cam , install new cam , apply vasaline to cam and hinge pins , repeat above steps in reverse . Door ... Read more now self closes .

After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wi ... Read more ggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.

Opened the box, removed the ice maker, removed the old ice maker from freezer, empty drawer of ice into the sink( the hardest part of the job) Phillips screw driver and removed the four screws holding the plastic front on and installed it on the new ice maker. Put it in freezer and I am back in business . This is real easy

Turned off water to ref , removed bottom kick plate , got a towel and disconnected the water line plastic fitting and un screwed the (2) tube clamps un screwed the coupling and ((carefully )) slid out the tube from the compression ferrels ! ( Be careful and do not break or distort them + remember exactly the order they are removed ! Sl ... Read more id the protector spring shroud from the plastic tube , took ogg the top hinge cover then remover the top hinge . Carefully lifted the door off feering the plastic tube through the bottom hinge with my foot ! Got the door off removed the bottom hinge + put the new on on, then removed the door cam which was broken on the bottom of the door , lifted the door up and carefully fed the water line through the new bottom hinge . Attached the top hinge and reassembled the rest same as I had dissambled it . Turned on water ( checked for leaks ) ! All working 100% a-ok ! This company is the best ! Ordered the part at 1 pm and had the part at 2 pm the following day many thanks : )