Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lack of power to unit
11 of 16 peoplefound this instruction helpful.
Neil from Williston, VT
Easy
15 - 30 mins
Screw drivers
This is the second time replacing this fuse, last time was exactly one year ago. The first time I replaced it, I removed the oven from the wall & disassembled a number of things to reach the culprit. This time I left the oven mounted & was able to access the 2 grille mounting screws on the top of the grille & remove it. Next comes the bla
... Read moreck plastic air deflector held by two screws & is mounted in front & on the right, it is shown on the parts list just above part #1434. After removing it, remove the two silver cover screws in the front, this cover also doesn't have a part # but is shown to the right of part #1410. At this point you can lift this cover enough to access the fuse which is on the left & held in place by one tiny screw through the clamp at the top, (careful not to drop it when removing). PS: Don't forget to cut the power to the microwave before starting!
Read less
Was this helpful?
Thank you for voting!
No cooking Power
12 of 19 peoplefound this instruction helpful.
Norbert from Minnetonka, MN
A Bit Difficult
15 - 30 mins
Pliers, Screw drivers
Had to remove outer cover (special screws involved). Found the correct part at PartSelect.Com and it arrived 3 days later as promissed.
This oven has diffcult electrical connections at switch to get disconnected. I found it easier with the sw loose and in hand so that the connectors can be released with a small screwdriver.
... Read morer /> One has to this in order to test the part wirh an ohm meter. I found the sw did not close but remained open and thus caused the oven not to function.
Removing interconnect switch is tricky but not difficult.
Outer cover replacement is not as easy as it should be, especially the sides.
All is well and working.
Microwaves are simple devices if you are know how to read and understand schemetic diagrams.
Read less
Was this helpful?
Thank you for voting!
Turntable did not turn when anything on top
10 of 13 peoplefound this instruction helpful.
Javin from Waltham, MA
Easy
15 - 30 mins
Screw drivers
Turn off the circuit breaker to the microwave. Remove the 4 black wood screws that secure the microwave to the cabinet. Pull the microwave all the way out and set it on something that leaves you access to the middle access panel on the bottom. Remove the access panel on the bottom that has one screw. Unhook the 2 cables to the motor r
... Read moreemembering which color goes where. Remove the 2 screws for the motor and replace the motor. Finish up in reverse...
Read less
Was this helpful?
Thank you for voting!
after 3-4 minutes microwave display would blink and unit would just cut out.
12 of 20 peoplefound this instruction helpful.
Larry from Brookfield, CT
A Bit Difficult
30 - 60 mins
Wrench set
This was the second time I've had to open up the microwave. 1st time display would blank out but system would continue to operate. Found solder connections on board to LED display were defective. Resoldered and unit was fine. This time I found the connection to the oven cavity temp cut-off was bad, plastic connection cover melted. When
... Read more unit operated bottom lead and wire would heat up. Couldn't measure a Discernable distance so either wire or connector connection surface was not sufficient to carry the current. 1st replaced sensor still wire heated up. Replaced connector and there was no sign how heat from resistances.
Read less
Was this helpful?
Thank you for voting!
Microwave function not working
8 of 9 peoplefound this instruction helpful.
Aaron from BLUE RIDGE, TX
Easy
15 - 30 mins
Screw drivers
1) Removed 4 screws securing the microwave to the cabinet.2) Slid microwave out, unplugged and placed on a work surface that allowed lower trim to hang over. 3a) Removed two screws and removed the cover on top of the oven. 3b) Unplugged high voltage plug from Magnatron. 4) Removed wires from overtemp fuse mounted to Magnatron. 5) Removed
... Read more the four screws securing the Magnatron to the oven. 6) Removed Manatron. It's a tight fit, but can be done without removing anything else. 7) Replaced Magnatron. This is where I needed the magnetic part retrieval tool. The nature of a Magnatron is the use of strong magnets surrounding the tube. Getting the four screws back into place wasn't possible with just a normal magnetic screwdriver tip. I used the retrieval tool to position the screws back in place. Be sure to not initially tighten any screw completely, until they can be evenly tightened. This ensures correct compression/seating of the shielding material near the neck of the tube. 8) Reverse removal steps. Plugged in and tested microwave function on a cup of tap water. 9) Reinstated in cabinet and got a big thank you kiss from the wife!
Read less
Was this helpful?
Thank you for voting!
Blown fuse in microwave
8 of 9 peoplefound this instruction helpful.
Frank from VIPER, KY
Very Easy
15 - 30 mins
Screw drivers
One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.
Was this helpful?
Thank you for voting!
Oven wouldn't sensor reheat & error code on display
8 of 11 peoplefound this instruction helpful.
Chris from Springfield, VA
Easy
15 - 30 mins
Screw drivers
I looked at the exploded pic on your web site to find the location of the sensor. Next I removed the cover by unscrewing 15 screws then swaped the sensor and re assembled! Works great! Fixing it my self I saved at least 150$ and did not have to wait all day for a repair man who probaly would not have the part on the first visit.
Was this helpful?
Thank you for voting!
microwave would not heat
14 of 29 peoplefound this instruction helpful.
John from Erie, PA
Easy
30 - 60 mins
Screw drivers
First remove all screws holding on outer metal casing of microwave. Next remove the back and bottom metal pieces. You will then be able to pull aside the outer casing so you can access the door switches. Check each switch with an ohm meter in both the open position and with the switch closed. If the ohm meter reads the same in both the
... Read more open and closed position, the switch is bad. Check the top switch first. Replace switch and reassemble. Cheap fix for a costly microwave. Great customer service at Parts Select!
Read less
Was this helpful?
Thank you for voting!
Microwave not heating.
6 of 7 peoplefound this instruction helpful.
Seven from MOUNT AIRY, MD
Easy
15 - 30 mins
Screw drivers
Followed the instructions on your website and a YouTube video. The diode was at a 90 degree angle which made it a little trickier. Unfortunately the repair did not resolve the problem. I ended up buying a new microwave for temporary use for less than ordering any more parts. We are pleased with your website, instructions, ease of inst
... Read moreallation though!
Read less
Was this helpful?
Thank you for voting!
Sparking from the magnetron
5 of 5 peoplefound this instruction helpful.
Reid from LITTLETON, CO
A Bit Difficult
30 - 60 mins
Screw drivers
Symptom: Terrible sparking coming from the right side of the microwave even with nothing in the microwave. The part that was behind the cover was the business end of what I learned was the magnetron,
Repair process: Without appliance repair experience I went onto Google and searched for parts for my model PEB1590DM2WW. I
... Read morewas able to find a great parts schematic on partselect.com. At first I ordered a magnetron and while waiting for the parts to arrive I also learned that the capacitor can also fail easily as described in the other install feedback on the partsselect website. So I ordered a capacitor just in case. These convection microwaves are around $600 new so a $80 in parts is not out of line for 8 years of service. I installed the magnetron first and turned it on. sparking immediately continued so I quickly shut the unit off. After replacing the capacitor and letting it charge for several minutes before trying to start the microwave cycle was the issue. I choose to leave the replaced magnetron as the original unit was discolored and felt the replacement was inexpensive insurance. I also learned that if the wave guide (which is a plastic/metallic composite material) that covers the opening to the magnetron is burnt or has metal melted to it as mine did it will act similar to the microwave having metal inside the enclosure and will continue to spark and basically melt the wave guide further. Replacing the wave guide was very easy as well.
I am very thankful for the knowledge base and support available from Partselect.com as they made this repair possible on my own. Thank you partselect.com
Read less
Was this helpful?
Thank you for voting!
No heat.
6 of 8 peoplefound this instruction helpful.
Woody from MOSES LAKE, WA
A Bit Difficult
1- 2 hours
Nutdriver, Screw drivers, Socket set
Microwave with no heat. Removed casing and checked low voltage side from the fuse through all the microswitches to the primary side of the transformer, all good. Checked HV diode good. Checked secondary side of transformer, good. Checked capacitor, good. Even though the Magnatron electrically checked out good, it had a cracked magnet. Rep
... Read morelaced the magnatron and we have heat again!
It is easy to repair the burnt out bulb if one has the correct bulb. Your website is very user friendly and your service is great. I was not able to replace the bulb at this time because our RV is at the repair shop for some other matters. I am sure the installation of the new bulb will go smoothly. Thanks for asking. Sharry Kiehl
Was this helpful?
Thank you for voting!
runs but does not heat
4 of 4 peoplefound this instruction helpful.
Scott from PIEDMONT, CA
Easy
15 - 30 mins
Screw drivers
I removed the main cover ( torx security bit required) and tested the magnetron, capacitor, diode and door interlock switches according to instructions found on the internet. The capacitor and diode tested good but the magnetron looked burnt and corroded on the tip. The magnetron I received was an exact replacement for the original. It wa
... Read mores easy to replace the magnetron which arrived in 2 days standard shipping. I also cleaned the fan while I had access to the inside area. Hoping to get another 18 years use from the microwave!
Read less
Was this helpful?
Thank you for voting!
Opened door to get food put more food in closed door it wouldnt work
4 of 4 peoplefound this instruction helpful.
Henry Totten from GROVES, TX
Really Easy
30 - 60 mins
Screw drivers
Everything worked on the display light inside worked but when you closed the door and set time it would start counting down but not heating nor would the turntable turn. Started reading troubleshooting chart and first thing I did was removed the cover and checked door switches and found primary door switch wasn't working so I ordered a ne
... Read morew one installed it and it worked. Anyone doing this has to be very careful because of the stored energy in the capacitor is strong enough to kill. My micro is only 2 years old so I was hoping it wasn't anything major.
Read less
Was this helpful?
Thank you for voting!
MICROWAVE WAS NOT HEATING THE FOOD
4 of 5 peoplefound this instruction helpful.
Daryl from Salado, TX
Easy
1- 2 hours
Screw drivers, Wrench (Adjustable)
So my microwave was turning on and operating but nothing would get hot or even Luke warm. After watching several online videos on the problem I replaced the line fuse, diode, and the magnetron. I figured why waste time and just do all 3 while I have the thing apart. I discharged the capacitor with a light bulb first before doing anything.
... Read more Also had to pop the safety pins on the outside screws to take the metal housing off the microwave. Then Wallah! Everything is working and the food or liquid is hotter than it ever was. The only think that bothers me a little bit is that after the microwave shuts off, I can hear a few crackles or faint pops for about 5 seconds. I wonder if this is anything to worry about. Comments appreciated.
My Orders
