CS2150EPA (2004-03) Jonsered Chainsaw - Parts

This replacement screw is a high quality hardware that is commonly utilized on Husqvarna chainsaws. It is an authentic OEM item that has multiple uses, for correct location and application of this screw please make sure to check appropriate diagrams. One durable metal hex socket head screw is included per order.

This is a genuine OEM part. The Husqvarna pump cylinder is compatible with many chainsaw devices. The metal item connects the pump piston to the oil hose in the clutch pump. A pair of pliers and a hex key may be necessary for making the replacement. The pump cylinder is sold individually.

This is an original Husqvarna replacement part manufactured for use with chainsaws. Some ignition models do not include the spark plug connector also called a spark plug boot, it is recommended to inspect the spark plug boot or replace it when servicing the ignition module. The rubber spark plug connection kit includes the coil spring. Th...Read moree coil spring has a sharp end that pierces the insulation of the ignition module\'s wire, and it is the coil spring that makes contact to the wire. This spark plug connection kit is sold individually.

It is an authentic OEM sourced item which is specifically produced for use with Husqvarna and Jonsered chainsaws. The spring fits onto the knee joint and is made of metal. During installation, a wrench set, a screwdriver, and a set of pliers may all be needed to help replace this part. It will need to be replaced if it becomes broken or stretched. Keep in mind that this part is sold individually.

It is a genuine OEM sourced replacement screw which is specially designed for use with Husqvarna and Poulan chainsaws. The purpose of this component is to secure the hand guard, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality screw is made of durable metal and is sold individually.

This is an Authentic OEM sourced replacement part designed for use with Husqvarna Chainsaws. This is the Hose that delivers fuel from the Tank to the Engine. It is made out of Rubber and it is Sold Individually. Please note Fuel Filter is Sold Separately.

This is an authentic OEM part for use with Husqvarna Chainsaws. The clutch connects to the crankshaft and engages the clutch drum to spin the chain. The most common reasons for replacing the clutch are when the chain does not turn, won't stop turning, or does not cut properly. This part is sold individually. The tool that you will need to replace the clutch is a 13mm socket, large flat-head screwdriver, and a hammer.

This is an authentic Husqvarna replacement part that has been sourced from the original manufacturer to be used with chainsaws. The metal spring is part of the rear handle and is used to provide tension on the trigger to keep the trigger pressed outward. This item is available as an individual replacement part.

This cable assembly is designed to provide reliable electrical connectivity within the ignition system, ensuring smooth and consistent equipment operation. Built for durability, it helps maintain proper signal flow and responsive control during use. Ideal for replacing worn or damaged cables, it restores dependable performance and supports safe starting and shutdown of your equipment.

This replacement screw is specially designed for use with Husqvarna chainsaws. It is supplied directly from original equipment manufacturer. This kit allows you to tighten or loosen the the chain tension. Usually if the bar doesn't adjust when you turn the tension screw, either the bolt or tensioner nut is worn or damaged. Includes one (1...Read more) metal screw. Please note you will need a flat head screwdriver to secure/remove this item.

This is a genuine manufacturer-sourced part which is specially designed for use with Husqvarna and Jonsered chainsaws. The partition wall intake connects to the bellows helping to supply air into the carburetor. Over time it may wear out or get damaged eventually requiring a replacement. Make sure to refer to the appropriate diagrams for ...Read moreyour model to ensure the correct application. One durable partition wall intake with a metal clamp is included. Pliers and a screwdriver may be needed to remove the old part and secure the new one.

This is a genuine Husqvarna part that is OEM sourced to ensure a high level of quality. This item is intended to be used with chainsaws. The guide bushing is used to secure the cover to the chain brake housing assembly. This item is sold as an individual replacement part.