CS-8000 (Type 1E) Echo Chainsaw - Parts

This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.

Used in over 150 models of outdoor power equipment, this clip is commonly used to clip fuel lines or other hoses/tubes in place. It is sold individually, not as part of a kit or assembly, made of metal, and is silver in color. When this clip becomes damaged or worn, it can no longer support the fuel line, which may cause a fuel leak and...Read more/or smell. This wear will occur as part of regular use of your equipment. To complete this repair, you will need a wrench, screwdriver, and pliers. It is found in a variety of locations depending on your model; please refer to your owners manual for the exact location. Customers rated this repair as Easy.

This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.

This plastic clip is an OEM part direct from the Echo manufacturer. This part is compatible with many chainsaw devices. The clip is secured onto the adjustment screw, and helps to work as a grip for the screw. Please refer to specific instruction manual for repair instructions. This part is sold individually. A screwdriver and a wrench are often needed to make the proper removal and replacement.

This replacement adjustment screw is an authentic OEM sourced item that is specially designed for Echo chainsaws. Its purpose is to allow user to adjust the chain tension. Saw chain tension should be checked and adjusted as needed before each use. If the chain is too tight it will compromise the engines power due to increased friction and...Read more it runs high risk of breaking. If the chain is too loose it can come off the bar becoming a serious danger for the user. Please note this durable metal adjustment screw is sold individually.

This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.

This replacement screw is specially designed for use with Echo handheld lawn and garden equipment. It is a high quality OEM sourced item, not an aftermarket imitation. This screw is a standard hardware which has multiple uses depending on the equipment. Please note, this hex socket head screw is sold individually.

This authentic item is supplied directly from the original equipment manufacturer for use with chainsaws and engines made by Echo. The stud attaches to the crankcase. A wrench may be necessary during the installation of this part. It is made out of metal and will need to be replaced if it breaks or strips. This part is available as an individual replacement.

Genuine OEM replacement part, this item is sold individually. The Vent Cover is installed on the vent tube on the carburetors for the outdoor products listed below. After the Vent Hood is installed on the vent line, the the Fuel Tank vent is attached to the Vent Hood.

This spark plug boot is an authentic OEM supplied replacement part, not an aftermarket equivalent. This rubber cap helps is used to connect the spark plug to the armature-magneto. Over time rubber material can dry out and crack requiring replacement. Please note, this part is sold individually.

This is a genuine manufacturer sourced replacement o-ring which is specially designed for use with Echo chainsaws. Its purpose is to provide an air tight seal for the oiler. It is made out of rubber material and it is sold individually.