CRE500B Maytag Range - Instructions

replaced drip pans with correct type

The first thing I did was to turn the power off to the stove by turning the Stove circuit breaker off at the Main breaker panel. I next removed the 4 burners by pulling them out of their plug-in blocks. I then removed the four screws that held the top of the stove to the body so I could access the bad plug-in block, the screws were loca ... Read more ted under each of the burners drip pans. I next removed the screw holding the bad block. I lifted up the top of the stove so as to relocate the bad block, with wires connected, through the opening of the back burner. The bad block was located in the front rt part of the stove and by rerouting this to the back I could lay the top down and have easy access to what I needed to replace. I next used the knife to make a cut down the length of the old shrink tubing so as to gain access to the old splice. I next removed the old wire nuts which allowed the removal of the bad block. I then install the new clips into the new block. I installed one each shrink tubing onto each of the pigtails from the new clips and twisted the one new wire to the stove wiring harnes were the old wire was connected . I connected the seconded wire in the same manner. I pulled on each wire to verify that they were tightly secured together. I then positioned each shrink tubing over each wire nut (you have to fold the wire nut and wires down against the wire so as the shrink tubing will slip over the wire nut) and used a heating tool (hair dryer on high) to shrink the tubing around the wire nutted connection. I next installed the metal clip that would hold the block to the stove top. I placed the new block back to the location where the old block came from and secured it with the new screw provided by the kit. I re-installed the four screws to hold the top down, plugged in the four burners, turned the power on at the breaker box and turned the burner on to test that it work.

I didn't. Don't know how to get to light bulb to change it for this specific model

My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!

replaced old, worn blocks with new style surface plug in block kits - all 4 burners. Completely resolved the problem at very low cost (less than $50.00).

This wasn't a "repair", but I got an email asking for my story, so here it is. :-)

I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.

1. Turn off circuit breaker, pull out element and remove reflector pan.
2. Unfasten terminal block mounting screw and remove terminal block from casing.
3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire.
4. Slip on heat shrink slee ... Read more ves, strip stove wires and connect to new terminal block per instructions.
5. Heat shrink sleeves per instructions.

I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just ... Read more 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .

removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works ... Read more great now!

simply unplug 220 volt plug fom wall for safety, remove back cover screws, remove each electrical lead at the back of range, open oven and remove the screw at each end of element and remove. reverse procedure to complete repair. very easy fix!

Unplugged stove for safety Removed screws from old element pulled element until connected wires were exposed. Detached old element and connected new one. Screwed it in place and done! Im a 33 year old woman this is one of the easiest fixes ive ever done.

This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled ... Read more out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I reoved old drip pans and installed new ones. Very easy, they look great!