My Orders
CP220W-C Jenn-Air Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Infinite Rotary Control Failed
0 of 1 people
found this instruction helpful.
-
George from Centreville, VA
- Easy
- Less than 15 mins
-
Screw drivers
Replaced one of the four burner control switches on my Jennair cooktop. One of the tricks I use to prevent mistakes is putting the new switch along side the existing one and swap one connector at a time over to the new switch preventing any confusion and negating any need to mark the wires. This differs from your video assistant who disco
... Read more
nnected all the wires at once.
gc.
gc.
Read less
Was this helpful?
Thank you for voting!
Sparks shot out from under knob, then, no surprise, the burner didn't work
0 of 1 people
found this instruction helpful.
-
Charles from Bourbon, MO
- Easy
- Less than 15 mins
I've ordered parts from you twice now, and both times the service has been absolutely amazing!!!!!
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch. ... Read more r />Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch. ... Read more r />Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Read less
Was this helpful?
Thank you for voting!
control switch was no good
0 of 1 people
found this instruction helpful.
-
Valentine from Bow, NH
- Really Easy
- Less than 15 mins
-
Screw drivers
I remove fore screwsfrom the front panel. Then remove two screws to remove the switch and removed the wire plugs then put everything back together again.
Was this helpful?
Thank you for voting!
bad surface burner switch
0 of 1 people
found this instruction helpful.
-
Lawrence from Birmingham, AL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
1. Turn off power at breaker. Take no chances. Turn on each working burner, fan, oven light to be sure there is no power to the appliance. Then, turn them off.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release t ... Read more op edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release t ... Read more op edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.
Read less
Was this helpful?
Thank you for voting!
RF burner would not heat
0 of 1 people
found this instruction helpful.
-
Tim from Lorton, VA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
1. Flipped breaker and confirmed no power at cooktop.
2. Removed the Fan grille and removed the two screws holding on the control panel. It tilts up and out to the rear.
3. Unscrewed the 2 screws on top holding old switch to panel.
4. Disconnected the wiring one lead at a time and connected it to the new switch in ... Read more the same spot. There are 5 wires total and I carefully used needle nose pliers to remove reluctant wires and to adjust connectors if they were loose on new switch
5. Screwed the new switch onto the panel and screwed the panel back onto the cooktop.
6. Tested new switch...worked great.
2. Removed the Fan grille and removed the two screws holding on the control panel. It tilts up and out to the rear.
3. Unscrewed the 2 screws on top holding old switch to panel.
4. Disconnected the wiring one lead at a time and connected it to the new switch in ... Read more the same spot. There are 5 wires total and I carefully used needle nose pliers to remove reluctant wires and to adjust connectors if they were loose on new switch
5. Screwed the new switch onto the panel and screwed the panel back onto the cooktop.
6. Tested new switch...worked great.
Read less
Was this helpful?
Thank you for voting!
One burner only heated to a high temperature.
1 of 4 people
found this instruction helpful.
-
John from Bowie, MD
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I removed 2 screws to release the plate that held four the switces. I removed 2 screws to release the bad switch. I removed one wire at a time and connected the to the same post on the new switch, screwed the switch into place and reinsalled the mounting plate. The stove works fine.
Was this helpful?
Thank you for voting!
no heat to burner
0 of 1 people
found this instruction helpful.
-
richard from harlingen, TX
- Easy
- 15 - 30 mins
-
Nutdriver
Removed top and front panel
Was this helpful?
Thank you for voting!
grill was getting red hot with out control
0 of 1 people
found this instruction helpful.
-
gilbert from san antonio, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Followed instructions, once saw and how to replace and replug wires as the instructions it was easy as per your instructions
Was this helpful?
Thank you for voting!
No controlling Left side back burner
0 of 1 people
found this instruction helpful.
-
Gary from Vienna, WV
- Easy
- 15 - 30 mins
-
Screw drivers
Really easy ...followed advice posted from others with same problem. Before anything disconnect the power at the breakers and use a voltage detector to verify there is NO POWER!!!! Only need to remove the two phillips screws on the four controller panel, Slide panel away from you to access the controllers. Match wire/connector for connec
... Read more
tor from the old to new controller. Reassemble, restore power .. Happy wife!!!. She has been on my case to fix this thing for several years.
Read less
Was this helpful?
Thank you for voting!
The switch would not turn off the range. The switch just kept turning but nothing happened.
0 of 1 people
found this instruction helpful.
-
Jose from Victor, NY
- Easy
- 15 - 30 mins
-
Screw drivers
I removed two screws that held the switch plate together. Then I removed two screws that held the faulty switch to the swtich plate. I then unpluged one wire at a time from the old switch and pluged it into the new switch. Reattached the switch to the switch plate and then reattached the switch plate to the stovetop. Bingo! Everything wor
... Read more
ked beautifully. It was so easy and I saved ~ $100.00 by doing it myself, as opposed to a quote that I got from a local repairman.
Read less
Was this helpful?
Thank you for voting!
Front right burner did not turn on
0 of 2 people
found this instruction helpful.
-
Vanna from St. Johnsbury, VT
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
We followed the instructions on the video after receiving our part - they were perfect instructions and led us right through the repair. I have to say it would have been harder to do with one person - but probably doable.
Was this helpful?
Thank you for voting!
Bad burnes off on switch
0 of 2 people
found this instruction helpful.
-
Jim from Two Rivers, WI
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Easy as Pie.
Was this helpful?
Thank you for voting!
Burner only operated on high, no medium or low heat.
0 of 3 people
found this instruction helpful.
-
Paul from Collegeville, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
First I moved the left rear burner to the right front. No change. Then I moved the burner units from left to right, No change. I guessed it was the control switch and ordered from PartSelect. Turnaround time from PartSelect was excellent.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pul ... Read more led the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pul ... Read more led the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
Read less
Was this helpful?
Thank you for voting!
Heating element was burned out
-
Milton from Winter Springs, FL
- Really Easy
- Less than 15 mins
Simply removed the old element and plugged inthe replacement.
Was this helpful?
Thank you for voting!
Burner would stay on high, on all settings.
-
Robert from Attleboro, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
In response to your question.......everything went perfectly!! The reason?? I read the directions that were very easy to follow. It was a quick, easy repair, and the stove burner is working like new.
Thank you for your help!!
Bob
Thank you for your help!!
Bob
Was this helpful?
Thank you for voting!