CMXGGAS030790-05 Craftsman Generator - Parts

This is a replacement air filter/AC cartridge for your small engine. The air filter prevents dirt and debris from entering the engine. Over time, the air filter can become clogged or damaged, and this can lead to reduced performance. This air filter is approximately 4 inches wide and approximately 5 inches long. To replace the air filter,...Read more locate the air filter cover on the side of the engine, unscrew it, and remove the old filter. Be sure to clear out any dirt, clippings, or other debris that has found its way into the air filter assembly before you insert the new filter. Reattach the air filter cover, and secure it with the screws. This product is sold individually.

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the electricity flow when it detects excessive current. It can handle a maximum current of 20 amps. You can tell if a circuit breaker is broken by c...Read morehecking for visible signs of damage, such as an unresponsive button, cracks, or burnt marks. If the circuit breaker repeatedly trips, the breaker may be faulty or overloaded. You will need a screwdriver, a set of pliers, a socket set, and a nutdriver to replace the breaker in your generator. Follow the instructions in your user manual to access the control box. You typically need to remove the carburetor and the fuel tank before removing the cover of the control box. Please note that this OEM replacement part is sold individually.

This carburetor is a critical engine component designed to mix air and fuel in the proper ratio for efficient combustion. Built for Briggs & Stratton engines commonly found in lawn and garden equipment, it also serves as a compatible replacement for select Troy-Bilt generators. Installing a new carburetor can restore smooth engine operati...Read moreon, improve throttle response, and enhance fuel efficiency, helping extend the life of your equipment. For best results, confirm compatibility with your specific model before installation.

This is an authentic Briggs & Stratton replacement part that is intended to be used with portable generators. The valve is used to connect the fuel line to the tank and to control the flow of fuel from the tank. This item is available as an individual replacement part.

The OEM E-Ring is a silver metal part used to secure the wheel on the shaft. If broken, the wheel may fall off, and the part must be replaced. It is rated as "Easy" to install and requires pliers and a screw driver.

This high quality replacement starter rope is an authentic item that is supplied directly from original equipment manufacturer for use with Briggs and Stratton engines that are commonly installed on Toro lawn and garden equipment. It is an important part of the starter system that allows user to pull-start the engine. Please note this durable nylon item is sold individually.

An authentic replacement part that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is the special component which is attached to the starter rope to provide a user with a comfortable grip to pull-start the engine. This durable part is made of high-quality plastic and it is sold individually.

This is a genuine replacement carbon brush which is supplied by the original equipment manufacturer for use with Briggs and Stratton portable generators. The purpose of the brush is to help conduct the current by maintaining physical contact with an armature inside the electric motor which powers the unit. It is a high-quality component w...Read morehich consists of a durable plastic holder and two carbon brushes with attached lead wires and springs.

The voltage regulator goes next to the cover. This is available individually and is made of durable materials. It is a genuine replacement part sourced from the original manufacturer for use with generators made by Briggs & Stratton. When replacing this item a screwdriver might be required during the installation process. It will require replacing if it becomes broken.