CGR1320BDW Magic Chef Range - Instructions

My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.

It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison

Had to take off burners and lift off top. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and removed old element. Then I did all steps in reverse to install new thermostat.

First I removed the burner to which the igniter was attached to. Then I attempted to removed the two screws holding the igniter in place. However, these screws proved to be difficult. I called a local appliance repair shop and the person I spoke to explained how the screws were designed to go one way. Any attempt to remove these screws wo ... Read more uld result in the threading to be stripped and virtually impossible to remove. (I have never heard of these type of screws before) Anyway, he recommended a hack-saw. Well, the hack-saw worked. After that, the replacing of the part was very easy. Igniter works perfectly and now my wife is ready to conquer the bake sales.
This was my first time using partselect.com.
Yes, I will recommend them to other homeowners.
Thanks. A.T

igniter would heat but oven wouldnt come on or would intermittently.opened door a little and lifted it off removed racks and bottom shield removed wingnut and burner shield,removed 2 screws holding igniter ,took off lower shield to allow access to plug,unplugged old one plugged in new one replaced shield and 2 screws holding igniter,put o ... Read more ven back together in reverse order,works like new :) ps if unit not unplugged from wall be careful igniter is hot with electricity and will bite you OUCH!

I located the igniter element, and remove the two screws that hold it in place. I then went around to the back of the oven and located the wire, and disconnected it. Then I pulled it out through the oven and removed it. I then replaced it with the new element; pushed the wires through to back of the stove and plugged it in. With that ... Read more done, I screwed the new igniter element into place. I then put my oven back together; pushed it back into place and turned the gas back on. And presto! my oven lights like new again. I saved myself the costly repairman visit, and the job was easy.

Removed the drawer and the flash plate underneath .
Unplugged the igniter then opened the & removed the over door . Lifted the bottom plate to expose the burner and igniter . Undo the 2 screws holding the igniter in place . Replace the igniter and reach underneath and plug the wire connecters together . Place all the proper things in ... Read more their place .. and it was finished ...
The biggest snag I ran into was the one of the 2 screws stripped out when when taken things apart .. but I have taps and found a few new screws and replaced them ......
Quite easy fix .. don't a pay repair man to do it .... !!

clock is in top of double oven. Dis-assembly and access to the clock was a puzzle. Four screws in the top of the oven were the solution. The clock panel then folded out and access to three plug-ins and four screws allowed access to the clock. remounted the clock with four screws and replaced plugs. (watch carefully order of wiring) Re-p ... Read more ower on the oven and set clock. NOTE: Cover said Magic Chef but Label said MayTag

I first matched the symptom (very long preheat time/gas odor) with the most likely problem (faulty oven gas igniter). I then wrote the model # and Googled gas oven repair and got to your website. I then located the faulty part within about 5 clicks and proceeded to order the exact part within another 5 or so clicks. I received my order f ... Read more rom PartSelest in 2 days and had the oven working with the new igniter in about 10 minutes....Then it dawned on me---"Hey, I should be a Maytag Repair Man."
Thanks for the prompt delivery and the correct installation instructions. I will absolutely use your service again. (Not too soon, I hope !)

First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.

I thought that the initial problem based on the users manual may had been the thermostat.
Removal of the old unit and installation of the new one was quite simple.
The only time lag was cleaning some of the surrounding areas of the oven as worked progressed.
As it turned out though, the problem wasn't the thermostat, but ra ... Read more ther the igniter.
But, that was a fairly easy job as well!

it was actually pretty easy, it took about 20 minutes to fix, i had to unscrew the bottom portion of the oven to get to the Igniter on the bottom, then unscrew the Igniter, take off the old pice, and snap the new one in, put it all back together, and that was about it, i had dinner done by the time my husband got home from work. thanks

ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job