CGLGF388DSF Frigidaire Range - Instructions

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in ... Read more the house.....I show them what I DID!! :-)

We removed the old part and replaced it then when warming the oven all of a sudden there was a loud noise and something went and so we called a repair man which I guess we should of done in the first place. Now he has ordered a part that cost 170 soo that is my story don't try to repair if you don't have experience.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Watched the you tube video from this website and did the same to my own oven. Much better replacement igniter than was installed in oven from factory and amazing packaging from partselect.com. Thank you!

Found the orifice plugged. Tried to remove the orifice for cleaning but it wrung off due to corosion caused by cleaning . Had to replace the burner mount , pipeing and install a new orifice. It was a good fix to get her small burner back but it was very expensive for parts.

Very easy just had to pull the wire up that holds it secure.

After looking over the installation instructions I was confident that I could perform this on my own, However, changing the burner orifices was a bit tricky. Getting the original ones out worked well, they stayed in the nut driver when it was lifted. One of the new ones fell out when inserting it. Thankfully it fell all the way down a ... Read more nd I could retrieve it. A small piece of tape was needed to keep it in the driver. The rest of the install went per instructions.

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,

On the front left burner would not ignite, after the installation of the new one, same problem, new one didn't fix.. I guess it's something with the electric igniter

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

I researched the actual problem and found the correct part to order. My husband researched repair videos and saved them until our part arrived. On repair day he pulled the oven away from the wall, turned off the gas to the oven at the shutoff, and unplugged the electric cord. He removed the oven door, baking racks, oven floor, shield unde ... Read more r the oven floor, and storage drawer. It was a little awkward for him to get at the igniter location in the center of the oven. Once he got the old igniter unplugged and the new one in place, he followed the video instructions to plug the electric cord in again to test the new part -- while everything else was still dismantled. The new igniter fired on in just a few seconds and glowed red, just as expected. Successful test! Then he reassembled all the parts, needing a third hand to hold the igniter assembly in place so he could put in the screws. He took his time, and thinks it took him about an hour. I took a golden opportunity to soak the racks and oven floor in Oxi-Clean for an hour, then scrubbed with steel wool (not the unpainted shields!), and eventually the oven front, and inside walls. Once we had everything in place we turned on the oven, listened gratefully to the speedy ignition, and let it run for about 25 minutes. This 20 year old oven looks and works like a new model again -- and it's mostly clean. All in all, this was a fairly easy repair. We've never done this before, and tread carefully through it. We didn't want to mess with gas. Hooray and congratulations! I'm rather proud of him :)

Very easy to order,part was delivered promptly and installation was easy.I unscrewed a few screws and lifted the bottom panel out and put the new one in.

Had to pull back off due plug in for bake Ignitor is on bottom right Conner , mfg ill design , part was is to install after that. Parts select is great to deal with first part showed up damage due to shipping , parts select sent another with better packaging , works great have used them in the past for Ref ice maker parts . Due it yoursel ... Read more f save money

First we replaced the wiring harness because a multi-meter said it wasn’t getting power. That was only partially true. The wiring harness was burned looking so we just kept it instead of sending it back. When the spark module got here the burner caps were removed and then the wires were noted where they went on the module and then the pow ... Read more er and gas were turned off. The spark module was removed and then the stove was tested and we were back in business.

Removed both oven racks the removed two screws in back. Lifted rear of panel until front lip of panel was free. Installed new panel in reverse order. I was recycled the old steel panel at our local recycling station.