CGLES389FS1 Frigidaire Range - Instructions

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan

After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the ... Read more tab. It was sooo easy once I found that. I repeated in on the other side.

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

If you do not intend to take apart the oven door to clean the interior glass, I would recommend you use a clamp to hold the handle and oven door tightly together while you replace the screw. There is a spacer between the back and front panels which could otherwise be shifted out of position. I used a screw extractor to remove the damage ... Read more d screw and then installed the replacement. Wish all appliance repairs were this easy!

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 deg ... Read more rees. So far, works great.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe ... Read more into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical suppl ... Read more y. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Husband made install in very short time. Nice to have them back in operation.

Removed outer glass first ,then worked my way thru to inner glass..

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process ... Read more could then be reversed to assemble the parts and re assemble the door to the front of the range

I followed directions for replacement of the glass from the web. Replacement was simple and easy.