CGEF306TMFC Frigidaire Range - Instructions

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede ... Read more d are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the differ ... Read more ent sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, ... Read more and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Unplug the unit or turn off power at the electrical panel!!!! I removed the 2 screws that hold the top surface of the stove down. On my range, these are located in the front, under the the top surface. You have to open the oven door to remove them. I propped the top up with a couple of 10 inch pieces of 1 x 2 then removed the screws o ... Read more n each end of the bracket that holds the elements in place. I used a 1/4 inch nut driver for these. With needle nose pliers, I removed the 3 retaining clips from the bracket and removed them from the element with a screwdriver and transferred them to the new heating element. The holes around the outside of the element are numbered so it's easy to know where they go. Laying the new element next to the old one, I moved each paddle-type electrical connection one at a time to the corresponding place on the new one. Put the retaining clips back in the slots. Screw the mounting bracket back in. Put the top down and secure it with screws. Very easy repair.

This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. O ... Read more nce there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

Removed screws on the sides and front.
Labeled the wire sets connected to the front control panel.
Gently lifted up the stove top and flipped it over on to a towel.
Removed the piece of metal holding down the burner.
Disconnected the cables to the old burner.
Repeated steps above in reverse.

My husband followed the video instructions and it was easy to fix.

Twisted replacement bulb into place easily. Let there be light!

Have a double wall oven and the top oven would not shut off or broiler part would stay on and burn tops of food. Since bottom oven was not having any issues felt like it could
Not be control panel so decided to try the temp sensor. Since replacing oven has worked properly.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

removed the old burner and put the new one in it's place.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in ... Read more the house.....I show them what I DID!! :-)

Followed the parts select video. However there were differences. Four screws to release stovetop from brackets very difficult to break free even once correct bit identified. No spring clips but studded screw and coil springs let elements fall right off underside bracket. Need fours hands to hold back in place to screw bracket back in plac ... Read more e to hold elements.