EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CFW2000FW1 Crosley Washer - Instructions

All Instructions for the CFW2000FW1
121 - 135 of 362

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bearings in pump were lose and the washer was not pumping the water out
3 of 5 people found this instruction helpful.
  • Sherry from Milton, VT
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First I pulled the front panel on the washer off, than I unplugged the wires to the pump, took the two screws out that hold the pump, took the two hose clamps off and took it out. To replace I did the reverse.
Was this helpful?
Thank you for voting!
no spin cycle sometimes
4 of 8 people found this instruction helpful.
  • glenn from hampton, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...
Was this helpful?
Thank you for voting!
pump not working
3 of 5 people found this instruction helpful.
  • michael from sterling hgts, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
took off 2 screws and 2 hose clamps put in new part. Put srews and clamp back on less than ten minutes. total cost with shipping $62.00. repair person wanted $265.00.
Was this helpful?
Thank you for voting!
broken timer knob
3 of 5 people found this instruction helpful.
  • Anne from Costa Mesa, CA
  • Really Easy
  • Less than 15 mins
Unscrewed the broken knob. Screwed the new one one. Voila
Was this helpful?
Thank you for voting!
Leveling leg sheared off
2 of 2 people found this instruction helpful.
  • Joseph W from WEST PALM BCH, FL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Put machine on dolly. Tilted it on its back. Put screw driver into sheared leg and unscrewed broken leveling leg. Then screwed new leg in and tilted machine back up.
Was this helpful?
Thank you for voting!
Broken plastic door strike
2 of 2 people found this instruction helpful.
  • William from ROY, UT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Easy fix for a verry poor designed door catch. Almost purposeful on the manafactures behalf to make it out of cheap plastic Remove 2 screws replace install 2 screws
Was this helpful?
Thank you for voting!
Washer woild not spin out left clothes sopping wet
2 of 2 people found this instruction helpful.
  • Diana from THOMPSONVILLE, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was very good. They should have mentioned about the wire and spring to remove the rubber strip though. Found out about that in comments! Otherwise, very good!
Was this helpful?
Thank you for voting!
Door Latch broken. New part installed as per repair video - no problems.
2 of 2 people found this instruction helpful.
  • Donald from PHOENIX, AZ
  • Very Easy
  • Less than 15 mins
  • Screw drivers
New part installed as per repair video - no problems.
Was this helpful?
Thank you for voting!
The small plastic piece broke that locked the door.
2 of 2 people found this instruction helpful.
  • Tami from INDIANAPOLIS, IN
  • Very Easy
  • Less than 15 mins
Screwed the new part back into place.
Was this helpful?
Thank you for voting!
Broken piece of door latch lodged in switch
2 of 3 people found this instruction helpful.
  • Richard from LINCOLN, ME
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took door lock switch out and fished out broken part. Reinstalled switch and installed new striker. Problem solved. Ordered extra striker just in case.
Was this helpful?
Thank you for voting!
Washing Machine would drain but not spin.
2 of 3 people found this instruction helpful.
  • Kelly from Henderson, NV
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.
Was this helpful?
Thank you for voting!
Washing machine wouldn't go into final spin.
3 of 6 people found this instruction helpful.
  • Manny from Old Bridge, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First unplug the machine, then remove two srews on the back of the machine for the top cover. Remove top cover and then remove two srews that hold the door locking part. Put your hand in the machine and grab the part. unplug the three wire harnessess then plug them back and put back in place and put the two srews back and then the top cov er and two srews as well.
Was this helpful?
Thank you for voting!
Wouldn't drain water...thus no spin cycle!
2 of 3 people found this instruction helpful.
  • Sandra from Amherst, WI
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Let's see...removed lower panel-used tools to unscrew the unit---one piece-nice to replace---EASY to replace! Removed hose---placed hose on new unit; screwed all back to bottom of washer-replaced lower panel...Voila! Made sure unit was balanced...did a load of whites---Awesome WASHER NOW!!!
Was this helpful?
Thank you for voting!
Washer drum would not spin
3 of 6 people found this instruction helpful.
  • Annie from Santa Clara, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The dru m would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad.
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!
Was this helpful?
Thank you for voting!
Water leaking and broken shock absorbers
3 of 6 people found this instruction helpful.
  • Dan from Concord, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Removed spring retainer straps from top of springs. Propped up tub with blocks and a wedge. Lifted out each spring and replaced. Re-attached spring retainer straps. Removed pins from shock absorbers (old/broken ones). These break due to moving washer w/out installing original foam blocks and support screws or due to age and fatigue. Pins have a retainer that must be depressed as you pull or push them out. may need to spin back and forth with pliers as you pull them. Bottom right pin won't come out w/out a hassle. Cut it in pieces with dykes and used spare pushed in from the FRONT (not the rear, as it was originally installed). Found leak was not fixed by getting the drum back up to proper height. Found bolt on tub had broken the bottom of the soap dispenser "tray". This is a 50.00 part. Made a patch from the bottom. Roughed up plastic and used silicone adhesive. After it had adhered filled from top with more silicone. Allowed 24 hrs to dry. Washer is as good as new.
Was this helpful?
Thank you for voting!
All Instructions for the CFW2000FW1
121 - 135 of 362