- Home
- CFW2000FW0
- Instructions
CFW2000FW0 Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer was bouncing and emitted a banging noise only when on high speed spin
2 of 2 people
found this instruction helpful.
-
chris from COMMERCE TWP, MI
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I watched the videos and replaced the shocks and suspension springs. This worked to stop the unit bouncing completely and cut the banging noise in half. Further diagnosis revealed a damaged drum and outer shell. The repair itself was very simple and didn't require special tools or skills. There is a tricky shock absorber locking pin on th
... Read more
e right shock bottom position. There is a control box of some sort that prevents the complete removal of the pin without breaking it. On install, I simply pushed the pin through from the front. Ultimately, I ended up replacing the unit. However, I found the site to be extremely helpful. Great service.
Read less
Was this helpful?
Thank you for voting!
Water would not always drain from the wash tub.
2 of 2 people
found this instruction helpful.
-
Charles from PARKERSBURG, WV
- Easy
- 30 - 60 mins
-
Socket set, Wrench (Adjustable)
Simple install, remove the two screws holding the pump motor.
Loosen the two hose clamps that hold the hoses in place.
Pull out old pump motor.
Place new pump into place, and install mounting screws and tighten.
Slip drain hoses onto new pump and reinstall clamps.
Check for leaks.
Done.
Loosen the two hose clamps that hold the hoses in place.
Pull out old pump motor.
Place new pump into place, and install mounting screws and tighten.
Slip drain hoses onto new pump and reinstall clamps.
Check for leaks.
Done.
Was this helpful?
Thank you for voting!
Drain pump was out
2 of 2 people
found this instruction helpful.
-
Mark from VANDALIA, IL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Repair was easy watched video it was spot on I went to auto parts store and bought 2 screw clamps to replace the spring clamps and made repairs easier washer works great happy wife
Was this helpful?
Thank you for voting!
Tub was rocking a lot on spin
2 of 2 people
found this instruction helpful.
-
Michael from Viola, DE
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
The replacement of the Shock Absorber Kit was hampered on the right side by a metal box that was mounted just a little shorter than the bottom plastic pin. the deadblow hammer with the dowel worked with all the pins including the impeded pin and the top right pin which had to be removed at an angle. The replacement did not repair the wash
... Read more
er - it is the tub bearing which went in a previous washer of a similar model about 4 years ago.
Read less
Was this helpful?
Thank you for voting!
Catch on door strike broke.
2 of 2 people
found this instruction helpful.
-
Mildred from LOVINGTON, NM
- Very Easy
- 30 - 60 mins
Removed and replaced two screws.
Was this helpful?
Thank you for voting!
Washer door wouldn't lock so it would not run
2 of 2 people
found this instruction helpful.
-
Lynne from ST MICHAELS, MD
- Very Easy
- 30 - 60 mins
-
Screw drivers
Watched a u tube video and did it myself and I'm a 58 year old woman who has never worked on a washer before!
Was this helpful?
Thank you for voting!
Washer would not complete the spin cycle
3 of 5 people
found this instruction helpful.
-
Andrew from Fruitland, ID
- Really Easy
- 15 - 30 mins
-
Screw drivers
I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.
Was this helpful?
Thank you for voting!
No top Panel
5 of 11 people
found this instruction helpful.
-
RICHARD from RAVENSDALE, WA
- Difficult
- 30 - 60 mins
-
Screw drivers
(This is reply #2 of 2)
After I finally got all of the parts (at least the rear brackets and screws) I found that the panel only had one of two holes for the two horizontal screws.
After drilling a new hole in the left rear bracket position, I discovered that the 2 screws could not be threaded into the bracket pilot holes. They ... Read more t froze up at the top of the taper in the threads. I had to increase the size of the hole 1/64" to get the screws in. There also is a trick to getting the bracket through the punched out hole in the panel- you must angle the bracket corner to corner then apply about 10# of preasure to the bracket to force it through the hole.
Other than that, the panel install went pretty well. Now I have to get the front brackets and springs and screws which are on backorder...
After I finally got all of the parts (at least the rear brackets and screws) I found that the panel only had one of two holes for the two horizontal screws.
After drilling a new hole in the left rear bracket position, I discovered that the 2 screws could not be threaded into the bracket pilot holes. They ... Read more t froze up at the top of the taper in the threads. I had to increase the size of the hole 1/64" to get the screws in. There also is a trick to getting the bracket through the punched out hole in the panel- you must angle the bracket corner to corner then apply about 10# of preasure to the bracket to force it through the hole.
Other than that, the panel install went pretty well. Now I have to get the front brackets and springs and screws which are on backorder...
Read less
Was this helpful?
Thank you for voting!
Bearings in pump were lose and the washer was not pumping the water out
3 of 5 people
found this instruction helpful.
-
Sherry from Milton, VT
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First I pulled the front panel on the washer off, than I unplugged the wires to the pump, took the two screws out that hold the pump, took the two hose clamps off and took it out. To replace I did the reverse.
Was this helpful?
Thank you for voting!
broken timer knob
3 of 5 people
found this instruction helpful.
-
Anne from Costa Mesa, CA
- Really Easy
- Less than 15 mins
Unscrewed the broken knob. Screwed the new one one. Voila
Was this helpful?
Thank you for voting!
pump not working
3 of 5 people
found this instruction helpful.
-
michael from sterling hgts, MI
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
took off 2 screws and 2 hose clamps put in new part. Put srews and clamp back on less than ten minutes. total cost with shipping $62.00. repair person wanted $265.00.
Was this helpful?
Thank you for voting!
no spin cycle sometimes
4 of 8 people
found this instruction helpful.
-
glenn from hampton, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...
Was this helpful?
Thank you for voting!
Door Latch broken. New part installed as per repair video - no problems.
2 of 2 people
found this instruction helpful.
-
Donald from PHOENIX, AZ
- Very Easy
- Less than 15 mins
-
Screw drivers
New part installed as per repair video - no problems.
Was this helpful?
Thank you for voting!
The small plastic piece broke that locked the door.
2 of 2 people
found this instruction helpful.
-
Tami from INDIANAPOLIS, IN
- Very Easy
- Less than 15 mins
Screwed the new part back into place.
Was this helpful?
Thank you for voting!
Washer woild not spin out left clothes sopping wet
2 of 2 people
found this instruction helpful.
-
Diana from THOMPSONVILLE, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
It was very good. They should have mentioned about the wire and spring to remove the rubber strip though. Found out about that in comments! Otherwise, very good!
Was this helpful?
Thank you for voting!