CFES355EB2 Frigidaire Range - Instructions

Removed heating elements and replaced drip pans. And by the way, this is the only 'pans' I could find to fit. Thanks.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you

I just took the old ones out and replaced them with the new ones. It took less than 5 minutes.

Phillips screwdriver used to remove 2 screws at top left in oven. Pulled thermostat out until I could get to the connector. Used pliers to hold wire, reconnected new plug , threaded it back into back of oven and reattached the two screws.
Saved $150 on a service repair call.

Just pulled the old cook top burner out and put the new one in .it took about 1 1/2 minutes

Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great

1. Turned power circuit breaker off
2. Removed all control knobs (they pull off)
3. Removed cover retainers (below control knobs) with screwdriver
4. Removed cover plate
5. Removed clock/timer anchor screws
6. Rotated clock/timer unit to expose wiring connections
7. Marked locations of all wiring connections ... Read more and disconnected wires
8. Connected wires to new clock/timer unit
9. Installed new clock/timer unit with anchor screws
10. Installed cover plate with cover retainers
11. Replaced control knobs
12. Turned power circuit breaker on and tried all controls to verify o.k.

Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on ther ... Read more mal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven ... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

I was required to remove the control panel to access the plug as it had been broken and the switch had been shoved into the unit . It would have been extremely simple if the plug had remained on the outside surface
My son can now clean his dirty oven

unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to mak ... Read more e sure all worked AND IT DID!

Very easy just had to pull the wire up that holds it secure.

All you do it unplug the old one and plug in the new one.

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,