CFES3025PBE Frigidaire Range - Instructions

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede ... Read more d are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the differ ... Read more ent sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!

Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door ... Read more from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!

Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. Th ... Read more e biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

ordered switch for on, off. Turned power off at breaker.opened oven door, underneath top console there are four philip screws.. remove top and take slotted screwdriver and unscrew four plastic nuts. I used pocket knife..remove plastic cover , and then remove four more philip screws to remove metal plate that holds all four control switchs ... Read more . remove two screws that held switch in place
and unplug wires and plug new switch in... Saftey first gentlemen, there is no ifs and buts or maybes when it comes to your life.. make sure you turn your power off.. works like a charm , can adjust heat from 1 to hi..thanks for partselect great price and speedy shipping...James K. Luper

Removed screws on the sides and front.
Labeled the wire sets connected to the front control panel.
Gently lifted up the stove top and flipped it over on to a towel.
Removed the piece of metal holding down the burner.
Disconnected the cables to the old burner.
Repeated steps above in reverse.

My husband followed the video instructions and it was easy to fix.

First unplug the stove before staring any of this task. loosen and remove three cross tip screws at the upper front of the stove top. You will need a piece of 1x3 wood about 1 1/2 feet long to hold the stove top up (sets at an angle upwards to the front). Loosen remove the bracket holding the burner you wish to replace. Disconnect th ... Read more e electrical wires connected to the burner. The burner is held in place with bracket clamps, remove the clamps from the oven bracket holding it. The burner will have a series if numbers in the back side, remove the brackets one at a time and reinstall on the same number on the new burner. do this to all 3 or four brackets. Install the new burner, install the bracket holding the burner, reconnect the wires. remove the wood brace and all tools. lay the stove top back down on the stove. plug the stove in and test the burner to make sure it works. turn off the burner and install the screws hold the stove to in place. Ta-Da your done. Also you tube has movie shots to give you a much better picture of what I just wrote about...

Have a double wall oven and the top oven would not shut off or broiler part would stay on and burn tops of food. Since bottom oven was not having any issues felt like it could
Not be control panel so decided to try the temp sensor. Since replacing oven has worked properly.

Remove 4 knobs from front of stove.

Remove plastic nuts that are directly underneath oven knobs. Loosen with plyers and unscrew.

Remove front cover.

Remove 8 screws holding down electrical panel. Remove panel. Remove 2 screws holding switch into place. Transfers wires from old switch to new switch so you h ... Read more ook them up correctly. Then reinstall in reverse order. Job complete in 15 minutes.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

removed the old burner and put the new one in it's place.

Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to re ... Read more assemble.

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

Followed the parts select video. However there were differences. Four screws to release stovetop from brackets very difficult to break free even once correct bit identified. No spring clips but studded screw and coil springs let elements fall right off underside bracket. Need fours hands to hold back in place to screw bracket back in plac ... Read more e to hold elements.