CFEF372EC1 Frigidaire Range - Instructions

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 deg ... Read more rees. So far, works great.

used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe ... Read more into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

pulled door off took door apart replaced hinge

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical suppl ... Read more y. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

We removed the screws holding the old element. Pulled the old element out of the back of the oven and disconnected the connecters (they just pull off). Slipped the connecters to the new element and pushed the element back in the oven wall and installed the screws. The only hard thing was removing the screws, because they had been in the ... Read more oven for 15 years and were a little corroded.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door ... Read more . Just reverse the way you take it apart to put it back together.

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

2 People--removed door, then removed and replaced springs followed by door a brief pictorial of the area even printed on the package would have simplified the project

with a schematic of the door, this was fairly easy. since we had to take it completely apart, we cleaned the glass as well and every little nook and cranny. Once we put it back together, the door looked like we just bought it. these days, with whats available online, scary jobs turn out to easy.

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to ... Read more the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process ... Read more could then be reversed to assemble the parts and re assemble the door to the front of the range

Found a YouTube video similar to the required repair. Took door off, disassembled the door, replaced the right hinge-spring assy, reassembled. Worked great. High quality replacement part from Part Select that was made in the USA.