CFEF322ES5 Frigidaire Range - Instructions

Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on ther ... Read more mal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.

Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great

unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to mak ... Read more e sure all worked AND IT DID!

Extremely easy. Two screws and electric connection that had easy pop on-off connection.

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,

Followed instructions on website. Went perfectly.

Turn off circuit breaker
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the ... Read more bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven

My friend used a tester to determine where each wire was supposed to connect to. I'm not sure what he did with the extra connections.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.

I followed the instructions from the lady taking my order she talked me through the steps

Unplug the oven (very important). Unscrew the bad element and screw in the new one. Plug oven back in.

1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the o ... Read more ven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.

after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done

The original instructions were to replace burner and plug wires back in the same plug they came from.
The problem is that the plug order had changed between parts.
Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wir ... Read more es to reach.

We turned off the power, took out the element, installed new element.

Remove the lower bake element by removing the 2 retaining screws that secure the element to the inside oven back. Carefully slide the element out. There are 2 wires attached to the terminals of the element. While removing be careful to not pull the insulation out with the wiring. Attach the wires to the terminals of the new element and r ... Read more einstall in reverse order.