CFE28TP2MGS1 General Electric Refrigerator - Instructions

Popped it up and popped new one on

It just snapped in. Fit perfectly. Excellent service.

Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!

I looked online and it said GE does not make the support for my model Refrigerator/freezer. I looked the picture for this part and it looked like the same one so I bought it (very inexpensive) and an extra one just in case.
I took out most of the items on that sliding shelf and pulled it out. Found the correct socket for the nut an ... Read more d removed the remaining piece. Then just used the same nuts and new Glide support, tightened it up (but not too much, and tried the shelf.
It worked !!! I added the frozen foods and I was done. It was very fast. And by the way, I am not a big home repair person. EASY.

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back ... Read more in SNAPP

Left side was broken for about 8 years. Back of glide would fall down about every 4 months. This time the upper basket jammed up on the glide and the freezer drawer would not close. Had to break it to remove the upper basket.

From the time the parts were delivered and installed two Glide Supports, it took a total of 30 minutes. ... Read more If that long. Before I ordered the part, I made sure I had the socket to fit the nut and that I was able to remove it. I removed the broken one after ordering.

PartSelect was the only website that I could find that carried the part.

Exposed evap defrosted with heat gun exposed defrost element defrost termination switch ok therminster didn’t check out the thermistor sends the signal to logic panel then run the the freezer ice machine and refer temps it took 24 hours before the system starting to show results freezer compartment 10 below ice compartment 0 degrees refer ... Read more temp 37 degrees one refrigerant three different temps system is running at optimum performance 450.00 $ service call the thing with GE appliances there is no wiring diagram .thankyou parts select .ill use you on all domestic service calls.

It was way to ez to install only a couple of minutes that's it

took a little more effort than the video show to remove old module and replace new. Works fine now.

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P ... Read more lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of yo ... Read more ur company & it's repair video. THANK YOU SO MUCH

Snap filter into place while holding the filter slightly away from the refrig. When filter snaps into place, push it towards refrig into place.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

I replaced the thermostat, temperature sensor, and the run capacitor. . . Refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance. . . Everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and ... Read more saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on. . . Problem fixed. The compressor kicked on right away and started cooling the refrigerator.