CER3760BAQ Magic Chef Range - Instructions

Took the old levelling leg out and screw the new one in.

Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in ... Read more each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old ... Read more gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.

The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on th ... Read more e new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

unplug unit remove rear panel screws lift up stove top remove top two screws remove panel remove two hinge screws remove replace hinge and follow in reverse order

Bought bottom element as suggested. Instruction video seemed straight forward. Not exactly.When I unscrewed the element and gently pulled it out to access the connector, one came out an inch or two, however the left side would not slide out. Tugged a little and it released the connector which jumped back inside the oven. Had to slide the ... Read more oven out from counter, remove a rear covering plate (2 screws and no problem) and found the new element connectors protruded through the rear of the stove for connection. They were covered by the large rear plate I had removed. Screwed the plate back on and, slid the stove back into position, restored power and all was good. Stove heats properly. Happy.

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched ... Read more off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

Very easy repair. Turn the power off to the oven, take out two screws and unhook electrical connections. Replace with the new baking element and you are done. Takes only about 10 minutes and the oven works like new.

Plugs in easily, screws to secure

After watching the instructional video (and flipping the breaker to my range) it was straight forward and simple. The heating element was a little bent so didn’t originally sit square/flat to the bottom of the oven so I uninstalled, bent it gently a little and reinstalled and it set down flat. It still didn’t take 15 minutes.

Put a new one in.

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

removed screws and disconnected the wires removed element and did the replacement less than 15 minutes, and cost less than locally by 25.00 and received part the next day. EXCELLENT

I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....

When ordering the replacement part, read the posts on how to replace the bake element. Just follwed their lead. The only difficulty is getting a hold of the wire at the back of the range that the bake element plugs into. There wasen't much play in the wire.
PS Be sure and remove the range door or have very long arms.