CER3520AAT Magic Chef Range - Instructions

First I removed the old bowls and replaced them with the new.

took old bowls out, put new bowls in, took a coffee break

Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

First, I unplugged the oven. Then, I removed the two screws that hold the element in place. After that, I gently pulled the element toward the front of the oven until the wires were exposed. I disconnected the wires from the old element, removed the old element and then attached the wires to the new baking element. I gently pushed the new element back into the screw holes and screwed the new element in place. When I plugged the oven back into the wall I heard a pop and thought I'd blown up the oven! Turns out the breaker popped...after fixing the breaker, I turned the oven on and the element worked just fine. I highly recommend PartSelect.com for their fast shipping and great products. I will be ordering from them again for future appliance parts.

Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.

Replaced old drip pans with new ones - very easy - even a 68 yr old lady can do it!!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new element using the wire caps, and finished bye rescrewing the element backinto place.

Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one

we removed the old pans after first removing the electric heating element and simply inserted tne new pans

First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will cause the plastic plug connector to melt from oven heat.

First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum.

First, I shut off power to stove(a must).
Removed two screws that hold element in place.
Gentley pulled element toward door opening.
Once wire is expose, hold back of element and pull gentley to seperate element from wire slot.
Connect new element to wire and replace screws.

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the right side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.

This was easier than putting in a new light switch. The old receptacle would not make the necessary adjustments to the heat element to maintain the desired temperature. Even when I turned the temperature knob to "minimum", the heat element would bun at the maximum temperature. I pulled the element from the Receptacle, raised the stove top to expose the receptacle and wiring. My stove was too heavy to pull from the wall, so I had to go to the breaker box to flip off the breaker. I returned to the stove and snipped the non working receptacle (with a wire cutter) and attached the new receptacle with the ceramic wire nuts, that came with the assembly. I turned the electric-breaker back on, and tested the heat element. The element will now make the on/off adjustments on each temperature setting, to maintain the correct heat.
I ordered two receptacles because I wanted a spare. I do a lot of baking during special-day dinners, for my family members... and due to the age of my stove, I bought the bake element as a "back up" if the present Bake-element burns out.