CER2350AAL Magic Chef Range - Instructions

My wife and I did the repair. The most difficult part was finding the correct replacement part. The store where we bought the stove lied about what part was needed, which cost us a lot of online time before we found the part. UNPLUG THE STOVE or turn off the breaker. We removed the back of the stove, which is two or three pieces, comple ... Read more tely. The thermostat is part of the single oven control. This job inclludes replacing the oven thermocouple (temperature sensor) which is a small copper tube about a foot long which is inside the oven itself,held in two spring clips on the left upper side near the front. You install the new thermocouple, which comes with and is attached to, the replacement thermostat from the back and top of the stove. Unplug the top burner elements and remove them, along with the drip pans. Remove the single screw that holds the connector for each burner to the stove top. Then lift the front of the stove top and remove it. Remove the screws holding the inner top of the stove. It has a tab on each side that slides under the flange of each side of the stove, so you must remove all the screws from the back of one side so you can swing it out a bit. Then you can remove the inner top, Under that is insulation covering the top of the oven. Remove the old thermocuple. It is easier to cut it instead of fishing it all the way back. Just be careful to note how it is installed. Silde the new thermocouple in from the thermostat, under the insulation and through the small hole in the top of the oven box and clip it in place. The clips are flimsy so support them as you remove and install the part. Hold the new thermostat right next to the old one BEFORE you disconnect any wires. Unplug each wire in turn and plug it into the new thermostat before going on to the next wire. Watch for the short wire that connects from the thermostat to the oven indicator light. Then remove the old thermostat and put in the new one. Reverse the steps of the disassembly process to get it all back together. Be sure the insulation holds the thermocouple in the center of the hole mentioned above. That's it. Be careful of the sheet metal parts of the stove; Crosley didn't bother to deburr them and they can give you a nasty cut. Reconnect the power and test. If it all works, maybe you can talk your wife into baking something.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer ... Read more ed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

Shipped on timely manner,I will order again from Part Select, installing was a 15 minute job, that what I did, 1 unplugged stove, 2) removed 4 screws, (2 on top bracket and 2 on back) , 3) slide unit out couple inches enough to disconnected the wires from each end of unit and removed old part, installed new unit by reconnecting end wir ... Read more es, pushing unit slowly toward back of oven until wires find it's right position, set it back in place with the 2 screws on top bracket and 2 screws on back, done!!

I just bought my first condo and sure enough something broke in my oven. I thought "Oh great - I'll need to buy a new one..." After some research and a friend's advice - I was assured that I only needed to replace the broiler element. After researching the issue I googled replacement parts which led me to this web-site. I was amazed h ... Read more ow easy and inexpensive it was for me to replace the part. The directions were easy, simple, and spot-on! The instructions that were provided were easy to follow. I also utilized YouTube instructions as well for additional visual guidance. The shipping was super fast and the element was packaged very well. Thank you so much!

I marked all wires separately attaching a paper strip with tape to each connector and made a separate small chart where each wire should attach to the bottom of the switch. On this particular model there are three or four colored wires and two have both double and single connections to the same switch so the small chart told me where a s ... Read more ingle or double connector would attach even if I lost the attached taped information. Then since wires were marked separately, even if paper was lost I could still proceed with no outside help.
I had the luxury of leaving the breaker shut off while waiting for part to arrive. After arrival which was only a couple of days, I raised the stove top and let it rest on a small board maybe 1.5 feet so it would keep itself up.
The under assembly was already taken loose before so I just removed the broken switch taking all wires loose, which are already marked and replaced the switch with the new one. Gently placing each wire at its place after removing the tape for that connection. After all four wires were connected I held the switch up in place while screwing the two set screws into place. Then reattached the bottom assembly cover and then let the top down and reattached the four screws, one in each stove hole to attach the stove top to the under assembly. I then reattached one element and flipped the breaker switch on. No sound or problems so I tried the element and all is well. Reattached all elements and the project is done. PartSelect.com made this repair easy and economical. Replacement would have been 4x the part and shipping. Thanks.

replaced drip pans with correct type

First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.

I didn't. Don't know how to get to light bulb to change it for this specific model

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

Repairman wanted $99 just to come look at it, then the cost to fix it. I got online, found the part, 2 screws and $40 later and all fixed. Wife baked me an apple pie that evening, better than ever!

turn off breaker take two screws loose from back of oven slowly pull out element unplug element an plug new element in push element in place an put screws back in turn on breaker done

First I removed the two screws on the bottom heating element that hold the element in palace,one on the left side one on the right side, I then pulled the element out about 2 to 3 inches and disconnected the two wires. I then installed the new element. It took me about 20 mins. The cost of having some come out to fix this was about ten ti ... Read more mes of what I paid for this part. Thanks for the quick service.

Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.

First, I removed the two screws that hold the element in place. I then tried to pull the element out to disconnect the wires attached to the clips. The left side came right out. The right side would not. Had to pull the range out from the wall
(would only come out about a foot and a half due to the gas line connection). Removed ... Read more the back (2 screws). Removed the clip from the element from the rear and redirected the wire into the oven. Replaced the back, pushed the oven back, attached the wire clip and screwed the element in place. Works fine. This is definitely a job not requiring an electrician.

not to offend anybody but what i learned on prior posts helped alot..
1. remove unit and unplug.
2. remove door by opening to 45 degree angle and lifting door face towards you.
3. remove back panel to unit.e.
4.unscrew burner element from back inside of oven.
5.gently pry clip off each off burner element from r ... Read more ear of unit. Pull gently towards you.
6.unscrew support from inside oven.
7. remove old element and just reverse directions to reinstall.