First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.
The burner was shortening out and would work sometime. The first time I replace the burner but the new one shorted out quickly.
1 of 3 peoplefound this instruction helpful.
shawn from Vancouver, WA
Really Easy
Less than 15 mins
Pliers
I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the
... Read more stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.
Read less
Was this helpful?
Thank you for voting!
surface element burnout
0 of 1 peoplefound this instruction helpful.
david from wellsboro, PA
Really Easy
Less than 15 mins
The repair was just a matter of sliding the old one out and plugging the new one in. The ease of use of this website was wonderful. Super fast shipment. Im very pleased.
Was this helpful?
Thank you for voting!
Ugly looking drip bowl.
0 of 1 peoplefound this instruction helpful.
Irina from Green Cove Springs, FL
Really Easy
Less than 15 mins
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.
Was this helpful?
Thank you for voting!
Bowl -Drip and gasket
0 of 1 peoplefound this instruction helpful.
Walid from Worcester, MA
Really Easy
Less than 15 mins
Screw drivers
it was relay easy when you get the right pats .so Thanks for . PART Select. Best regard . Walid
After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short t
... Read moreime to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.
Read less
Was this helpful?
Thank you for voting!
one of wire melted and broken off from receptacle
0 of 1 peoplefound this instruction helpful.
Young from Cordova, TN
Easy
15 - 30 mins
Pliers, Screw drivers
Cut broken wire and existed wire off and put splice on both new and old wires to connect them. It's easy job.
Was this helpful?
Thank you for voting!
Sockets for the burner elementss were burned out
0 of 1 peoplefound this instruction helpful.
Martin from Manchester, MD
Really Easy
15 - 30 mins
I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires
... Read morewere connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.
Read less
Was this helpful?
Thank you for voting!
Old surface element burned out.
0 of 2 peoplefound this instruction helpful.
Royce from Rio Rancho, NM
Really Easy
Less than 15 mins
I ordered and received the replacement element, then unplugged the old one and plugged in the new one.
Job done.
Was this helpful?
Thank you for voting!
My heating element stopped working properly and one day just make a pop and stopped working altogether.
1 of 6 peoplefound this instruction helpful.
David from San Francisco, CA
Really Easy
30 - 60 mins
Pliers, Screw drivers
I followed the advice givin on the parts select website - it made it totally easy.
My Orders
